Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
13th December 2011, 02:48 AM #1New Member
- Join Date
- Dec 2011
- Location
- sydney
- Posts
- 3
Material advice required to build wheelchair suitable bench
Being in a wheelchair, i need to build a workbench that has good clearance underneath for my legs. It also needs to have relatively low top surface.
So what i require is some thoughts on what to build it with. I want to cover a 3m span with the thinnest material, that will maintain a firm, straight surface.
I'm thinking of building it 700mm wide, with a 200mm channel (40-50mm deep), 300mm from the front edge.
Therefore,i guess i'm askng for advice on;
2 lengths, 3000mm x 300mm x ?
1 length, 3000mm x 200mm x ?
I can build support along the back edge, so the 3000 x 200 won;t require the structural integrity of the front.
All, or any advice would be very much appreciated.
-
13th December 2011 02:48 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
14th December 2011, 10:06 PM #2
lowriderone
firstly, welcome to to the forum
I think a first and prob important question is, what is the maximum thickness you could tolerate in the bench top and still be able to comfortably work at it?
another question: what are you going to be doing at it? if it's light work then then a light weight top should work. If heavy chisel work then that has to be factored in.
A 3m timber span is going to bow in the middle unless it's thick enough to support itself. I suppose some angle iron support might lessen the bow tendency of thinner stock
for example, our bed is about 2.1m long, and the mattress is supported by 50mm angle iron and holds our combined weight. and hasn't bowed after ever how many years.
You might get away with a torsion box type construction (think hollow core door) with angle supporting on each long edge, with the gap in the middle.
I'm not sure this is clear, but hopefully isregards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
15th December 2011, 11:35 AM #3Intermediate Member
- Join Date
- Aug 2010
- Location
- singapore
- Posts
- 31
I'm not too sure about Australia standards. In Singapore, we have 700mm below the table for leg clearance. Writing height is no more than 800mm from the floor. So I'm guessing that based on these accessibility standards, you'll probably want your thickness to be 100mm or less.
-
15th December 2011, 11:40 AM #4Intermediate Member
- Join Date
- Aug 2010
- Location
- singapore
- Posts
- 31
Also, structural wise, build 2 benches 1500mm long instead of a 3000mm one may make the bench more stable .
-
18th December 2011, 12:57 AM #5GOLD MEMBER
- Join Date
- Jun 2005
- Location
- Helensburgh
- Posts
- 7,696
I like problems. First tell us what use it is going to get, then we can work around your needs. My first inclination is a torsion box but I imagine if you are using it as a conventional bench then when you hit something it will incur bounce. You could run supports at an angle underneath back to the wall/floor intersection from the front edge. A lot will depend on what material you have available, hardwood is better than softwood and some man made panels like flooring for instance might suit you better as it is more stable and does not react to weather changes, do you always have high humidity in Singapore? Wheelinaround from this board might have better suggestions as he faces similar issues. Where are you Ray?
CHRIS
-
18th December 2011, 01:08 PM #6Intermediate Member
- Join Date
- Aug 2010
- Location
- singapore
- Posts
- 31
Mini: The threadstarter lives in Sydney, not Singapore where I'm from. My local disablity accessibilty code gives him an idea of how high and how thick the bench may be. He can then decide how thick the torsion box may be or if he'll have other preference.
-
6th January 2012, 04:10 AM #7New Member
- Join Date
- Dec 2011
- Location
- sydney
- Posts
- 3
Thanks for the replies.
I'm fairly sure i'll be using lvl. Not the cheapest option, but seems to fit my needs.
-
6th January 2012, 04:15 AM #8New Member
- Join Date
- Dec 2011
- Location
- sydney
- Posts
- 3
Similar Threads
-
Bench - big, solid, cheap, no tools, no bench to build on
By Clinton1 in forum THE WORK BENCHReplies: 84Last Post: 17th June 2010, 11:16 PM -
making drumsticks and suitable material
By black_labb in forum MUSICAL INSTRUMENTSReplies: 29Last Post: 13th September 2007, 10:04 PM -
Tools required to Build Deck?? Help required.
By swazee in forum HAND TOOLS - POWEREDReplies: 11Last Post: 2nd February 2007, 07:30 PM -
Suitable Material
By Grunt in forum WOODWORK - GENERALReplies: 9Last Post: 30th December 2003, 05:09 PM