Needs Pictures: 0
Results 1 to 10 of 10
Thread: The Mitre Jack
-
3rd January 2017, 02:04 PM #1
The Mitre Jack
Here is some pictures of a Blackwood Mitre Jack I have .
I will add some links as well . One is the video of a Benchcrafted Miter Jack being used.
The other link is a drawing and dimensions that Cornish Workshop put on the net . The Cornish workshop copy looks to possibly have come from The Woodworker, a publication put out by Evans Brothers limited . The drawing in the link is imperial so I'll stick to that for the comparison. The construction of this Mitre shooting block is the same as My Blackwood one, except in some parts mine is thicker .The Bed of mine is thicker being 1 1/18 not 7/8
Mine also has a 45 degree bevel to the edge of the frame you can see, which I think could be handy when planing the protruding part of the secret dovetail join . The Blackwood Wooden thread on mine is 1"diameter and 5 teeth per inch. The length of the thread only is 13/1/2 not including handle or end bit.
The width of my movable and fixed block is 4" . The Frame of mine is just glued together and does not have the two rods with the nut at each end.
One thing I would do if building one is make the handle so it can be cranked like you see some have . Its a bit slow without it .
If there is anything That Ive missed just ask and Ill measure or take another picture.
Rob
-
3rd January 2017 02:04 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
3rd January 2017, 02:05 PM #2
-
3rd January 2017, 02:40 PM #3GOLD MEMBER
- Join Date
- Jun 2014
- Location
- Seattle, Washington, USA
- Posts
- 1,857
I reckon that with the proper threading capabilities I could knock that up in half a day. Seems like it would be well worth it too!
Thanks, Rob.
Cheers,
Luke
-
3rd January 2017, 07:54 PM #4
Yes, thankyou Rob. I think I've got the details pretty well sorted after seeing the pics of yours. I like the simple 'keel' to clamp into the front vise to secure it. Does this do the job satisfactorily? Any comments on potential 'improvements'?
Not sure I can do it in half a day, Luke (you're younger & move faster!), but I reckon I'll get a good way along with one over a day or so.....
In the second video, what is the purpose of the little bit of jaw you can choose to leave in place or add to the travelling jaw?
Cheers,IW
-
3rd January 2017, 08:01 PM #5
Sketch up drawing of bench crafted model https://3dwarehouse.sketchup.com/mod...ecb&login=true
-
3rd January 2017, 09:02 PM #6
O bugger I think I want one
-
3rd January 2017, 09:39 PM #7
-
3rd January 2017, 09:43 PM #8
The keel on what I have has corner blocks glued in one side to brace it , but they are spaced to leave room for a vise 9 inches wide to grab the flat bit . The other side forms a rebate with the frame and has two counter sunk screw holes drilled for screwing the whole thing down to the edge of a bench . This leaves the other side of the two blocks parallel with the bench top . So you can plane end grain 90 degree cuts.
The Keel as it is, needs to be changed to suit my bench vise.
No Idea But reading the info on the page in the link with the drawing , it says some makers did the blocks at different angles for things like octagonal mirror frames . And that they were made different to suit the work being under taken . I can only imagine mouldings from cornice size to small cabinet size . Or on that strange design possibly groups of rods , dowels ? Or groups of stacked beading like what hold panels in from behind, That would be handy being able to plane up 12 at once to the right angle .
Edit . That is what its probably for thinking more about it . The side board and credenza's and much furniture of the 1860s to 1900's were a item produced in runs of ? how many I dont know? There is books on it , I used to work restoring them . Stamped part numbers could be seen on them . Every one was getting into part work where one person produced one part of a piece all day long . In a small place you may still make a miter jack to shave bead at 45 degree in packs . I think this would still beat the stand alone cast iron picture frame type slicer .
-
5th January 2017, 07:52 AM #9SENIOR MEMBER
- Join Date
- Sep 2010
- Location
- Port Sorell, Tasmania
- Posts
- 592
little jaw appears to be at an angle to the base. That could allow for a 22 deg mitre.
You can't use up creativity. The more you use, the more you have. ~Oscar Wilde
-
6th January 2017, 03:20 AM #10
Some more plans for mitre shooting boards.
Both sourced from the Woodworker, one March 1964, the other I'm not sure of the issue date.regards from Alberta, Canada
ian
Similar Threads
-
How do I get Sketchup to tell me the compound mitre saw angles for mitre and bevel?
By barrysumpter in forum DESIGN & DESIGNING / GOOGLE SKETCHUPReplies: 7Last Post: 7th February 2016, 09:12 PM -
Mitre Jack Saw
By pmcgee in forum HAND TOOLS - UNPOWEREDReplies: 3Last Post: 4th November 2015, 04:06 PM -
Factory mitre cut accuracy and mitre joints
By Dengue in forum FESTOOL FORUMReplies: 1Last Post: 5th August 2012, 03:32 PM -
Electric jack suitable for router lift or jack bench
By Woodwould in forum WOODWORK - GENERALReplies: 4Last Post: 25th August 2011, 07:03 PM -
Lock mitre or splined mitre for ply boxes (entertainment unit)
By rogerwilco in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 7Last Post: 19th August 2010, 11:21 AM