Thanks: 0
Needs Pictures: 0
Results 1 to 9 of 9
Thread: Vice, what wood for jaw faces?
-
15th May 2022, 09:22 PM #1Intermediate Member
- Join Date
- Jun 2016
- Location
- Adelaide
- Posts
- 26
Vice, what wood for jaw faces?
I have a quick-release vice rescued from a dilapidated old workbench that was sold at an auction for a small sum. I am now ready to install it in my (nearly complete) new work bench.
The vice came with no wood on its jaws though.
What wood should I use as jaw faces and what thickness is recommended?
-
15th May 2022 09:22 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th May 2022, 09:36 PM #2
I went with 3mm cork for my latest vice, spray adhesive, trimmed to size. Yes it is a bit easier to damage, but it easy to replace.
I have, in the past, used 19mm pine and 25mm been a tree.
The idea is that the sub jaws are softer than the work piece.Pat
Work is a necessary evil to be avoided. Mark Twain
-
16th May 2022, 09:38 AM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,795
swings and roundabouts.
A softer wood is less likely to damage what you are trying to hold but not going to last as long so if you are happy to replace the faces more often then you could use a softer wood.
Most folks would use a harder wood and then use a softer, grippier, non-marking liner that is replaced as needed
The vice faces on my work bench use 3/4" thick Jarrah floor boards and originally lined with 3mm thick rawhide leather which works great. After 14 years of "hard use" both vices and their liners were still working fine but I had to replace the liner on the main vice as it got soaked in chainsaw bar and chain oil.
This time I decided to go with a material called "crubber" as it was cheaper than leather.
The crubber I used was 2mm thick Nitrile bonded cork gasket material and I bought a 510 x 1270 mm shed of it on ebay for $35.
I note it now costs $56. Unit price AU $34.70
Crubber is as grippy as leather but unfortunately not as strong so after 3 years of use is looking a bit tatty so when I replace it I will go back to leather.
On my mates vice we used a solid piece of 40 x 120 mm thick spotted gum and lined it with some of my left over crubber.
Vice.jpg
-
16th May 2022, 10:04 AM #4
I have cork glued on one, and that synthetic wood on another.
Both work well.
-
16th May 2022, 07:03 PM #5Senior Member
- Join Date
- Nov 2019
- Location
- Melbourne
- Age
- 36
- Posts
- 156
The vise jaw faces (if you're lining say metal vise jaws) is perhaps best if a durable hardwood - Anything really that you can get your hands on. I line the faces of the wooden jaw liner with full grain leather. You just scuff the wooden surface up with some 40 grit, wipe it with acetone or metho (especially if its an oily wood) and then use titebond or hide glue to stick the leather facing on. When the leather wears out, you can peel it off, sand or scrape the wooden jaw liners and then glue a new piece. If you have contact cement, that also works well.
Cheers,
Siggy
-
16th May 2022, 07:14 PM #6Senior Member
- Join Date
- Jun 2012
- Location
- Dungog
- Posts
- 274
I have used 17mm(not that The actual thickness is critical) plywood.
has survived several years of abuse
-
17th May 2022, 11:14 PM #7
As others have said most woods will do. Softer woods grip better but you can also use leather or something to give a bit more grip. The thickness of the wood will take away some of overall opening range of the vice so there is that to think about. If you intend having the wood jaws wider than the metal jaws then they need to be thick enough not to flex. You may also want to put dog holes in the wood jaw so again you need enough thickness to do that. I would have a look at what has been done on the bench builds on the forum and see what suits how you want to work. Here is a few I have done over the years.
Regards
John
-
18th May 2022, 04:09 PM #8GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
Soft work needs soft jaws. Hard work can stand harder jaws. I have several sets that I fit to suit what I am doing at the time. Its easy enough to interchange as they only have two screws in each face. A set with an abrasive glued to the faces and a set with leather (I prefer deer hide) make a good addition.
-
19th May 2022, 12:27 AM #9Senior Member
- Join Date
- Nov 2010
- Location
- Sebastopol, California, USA
- Posts
- 177
My vise has heavy leather (called "harness leather" in the U.S.), glued to thin high-grade plywood from a local craft store, and the plywood then attached to the vise jaws with contact cement. It's worked well. It also uses up less vise capacity, although I'll confess I've never, to my memory, used all the capacity (maximum jaw opening) of any woodworking vise I've owned.
Similar Threads
-
Carved human face on wood - Carved faces of a family
By Classicwoodwork in forum MEMBERS YouTube VIDEOSReplies: 0Last Post: 21st January 2021, 06:20 PM -
Wood for Cabinet faces?
By columnmn in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 2Last Post: 29th November 2016, 12:15 PM -
Wood Vice jaw - can I do this?
By RobTro in forum WOODWORK - GENERALReplies: 21Last Post: 6th July 2007, 09:27 PM -
wood vice
By 46150 in forum HAND TOOLS - UNPOWEREDReplies: 0Last Post: 27th April 2005, 09:09 PM -
Flattening wood faces: low-angle jack vs. 4 1/2 smoothing plane
By lyptus in forum HAND TOOLS - UNPOWEREDReplies: 22Last Post: 29th March 2005, 03:48 AM