Thanks: 0
Results 91 to 105 of 1194
Thread: WIP - Groggy's Workbench
-
18th August 2009, 10:39 PM #91
Hi Groggy,
Looking good alright, and very solid. I likes it.
Cheers
Pops
-
18th August 2009 10:39 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
19th August 2009, 11:28 AM #92
Squirrel, I am lucky to own a few squares but in my defence I can say they do get used. I'll try to explain why they were all out.
1. Lee Valley saddle square. Was using it to transfer markings where the haunches are.
2. LV small try square. Was using it mainly as a depth gauge to 20mm for the step in the haunch.
3. Starrett 4" try square. Used to guide the mortising chisel.
4. Chris Vesper square. Used for just about everything. It was used to check the progress of the 45 deg haunches, the start of the mortises etc.
5. Generic 8" square. Used to check larger leg assembly but also as a visual cue when mortising.
6. Colen Clenton square. This has a slightly thicker handle than most squares which allowed me to use it when the flutes in the legs were a nuisance. It also balances well.
7. Starrett 12" combination square. Note the ruler is removed. I was using it to rest the chisel on when starting and finishing the 45 deg cuts for the haunches.
8. Starrett 300mm combination square. This was being used for another job and happened to still be on the end of the bench.
9. Generic machinists square. I'd been using that one to square up the drill press table to the bit.
-
19th August 2009, 10:46 PM #93
-
19th August 2009, 11:08 PM #94
-
19th August 2009, 11:10 PM #95
As for moving the bench. Why would you want to once it is in place.
By Hoist
-
19th August 2009, 11:46 PM #96
-
19th August 2009, 11:55 PM #97
Moving the bench
If you look at the legs you will notice the dog holes are on all four legs, not just the front. This allows me to place a 19mm rod through and attach wheels to it. A simple cantilever will let me lift the bench up.
Another way I am thinking of is the dolley wheels used for trailers. If I weld two rods out the side to go into the legs I can crank the bench up. I saw some cheap ones today for about $15 each. The dog holes give me quite a few options as they are very strong lifting points.
-
20th August 2009, 09:00 AM #98Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Its all looking very impressive Groggy.
-
20th August 2009, 10:16 AM #99
-
20th August 2009, 10:47 AM #100
The first lot on the legs I fussed around with the router and guides doing it hand held - DON'T BOTHER! In case you missed that - DON'T BOTHER!
The side stretchers were done on a RTA300 Triton router table (note to self, make that thing flat or get a new router table ) and four pencil marks on the fence. No jigs at all other than the table and fence. The legs took a few hours to do, the side stretchers were done in minutes and with less risk of error.
Happy to explain further if you want.
-
20th August 2009, 10:54 AM #101
Gotcha thanks, thought you may had made some sort of tricky fully adjustable self levelling auto correcting idiot proof jimmy.
Every woodworker is looking for one of them.
-
20th August 2009, 10:54 AM #102
-
23rd August 2009, 12:06 PM #103
Set up the lower shelf yesterday and will work on the upper one today. Thought I'd take some pics so Jim could see the separators. I can fit 22 Bessey style clamps in the space and the mechanisms are protected from moisture and dust. The separators have a 5 deg bevel either side and the ends have a 45 deg bevel with a 50 deg side bevel to make it easy to slide the clamps in.
I may make a skid to sit under the bottom shelf as the weight may bow the shelf. I still have to make the end caps for the shelf and they will be the same material as the upper shelf.
I will label the heads of the clamps so I know what length they are and won't have to play lucky dip.
-
23rd August 2009, 12:47 PM #104
That looks good greg.
keeps them all in one place and it really is a dead spot in most cases. Also close to hand not walking halfway across the workshop fo another clamp.
Well thought out.Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
23rd August 2009, 01:38 PM #105
Thanks Jim. What I like is the things are out of the way and utilising what was previously dead space; plus the entire clamp is out of the way of moisture and dust. As the photo shows, the clamps pretty much seal off the end of the shelf.
I had to come inside and have a sit down, too much shellac fumes. Who needs a lathe when the workshop is spinning around?
Similar Threads
-
workbench
By Rhys Cooper in forum THE WORK BENCHReplies: 125Last Post: 4th August 2009, 09:42 PM -
Workbench on WC
By dhurrang in forum THE WORK BENCHReplies: 3Last Post: 13th February 2006, 10:42 AM -
Catch-22 - building a workbench without a workbench
By brianhay in forum THE WORK BENCHReplies: 11Last Post: 18th January 2005, 04:56 PM -
New Workbench ala FWW
By bigAl in forum THE WORK BENCHReplies: 27Last Post: 20th April 2004, 09:41 PM -
workbench
By spargs in forum THE WORK BENCHReplies: 4Last Post: 15th April 2004, 07:18 PM