Needs Pictures: 0
Picture(s) thanks: 0
Results 31 to 37 of 37
-
18th July 2018, 03:09 PM #31.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,790
A jockey wheel is used on a caravan/trailer to hold the hitch end up to make it easier to hitch/unhitch.
Screen Shot 2018-07-18 at 11.59.11 am.png
The height is varied by turning a handle on top as the door is rolled out.
The jockey wheel could be made detachable so you have the door on another wheel permanently attached to the door so you can just roll it open enough to attach the jockey and the use that to help support the door until it's full open.
You could also spring load the jockey to support the door at all times while it is being opened. Being on the very end of the door it does not have to support the entire load of teh door - just take some load off the hinges.
A basic one would easily accomodate the slope on your drive.
-
18th July 2018 03:09 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
18th July 2018, 04:36 PM #32Member
- Join Date
- Apr 2017
- Location
- Melbourne
- Posts
- 81
Oh I see what you mean, didn't think of adjusting it as I open the door. Well, considering this door will rarely open, typically just when bringing material in, that could work. Spring-loaded sounds even better, I've found some gate wheels with load rating of up to 100kg, that should be enough as just support for hinges. I'll look more into that, thank you!
-
18th July 2018, 04:40 PM #33GOLD MEMBER
- Join Date
- Aug 2007
- Location
- Saskatoon, SK, Canada.
- Posts
- 1,439
I did mean two doors, an extra one on the outside. That was until I saw the double wide in the picture.
-
18th July 2018, 06:27 PM #34GOLD MEMBER
- Join Date
- Apr 2018
- Location
- Nsw
- Age
- 64
- Posts
- 1,361
If you don’t need the full rollerdoor opening for access rather than complicate the issue with big gates just build a stud wall on the inside of your rollerdoor and box in the drum and insulate and line it the same as the rest of the shed with a single or pair of double solid core doors built into it for access It would be far easier, cheaper and you can get a much better soundproof seal
-
18th July 2018, 08:16 PM #35Member
- Join Date
- Apr 2017
- Location
- Melbourne
- Posts
- 81
It's definitely an option, I mentioned it somewhere above. My main problem with that is not the opening - I know I don't need 5.4m. It was more about trying to make something as wide as the roller door so that if I need to make this back into a garage at some point, I can just remove the door behind the roller door and I'm done. If I do a double wall and smaller door inside, then I need to remove the whole wall. But thinking about it again, and compared to complications of making huge doors, maybe that's not such a big deal (and for only a possibility I'll need to do it some time in the future).
Cheers
-
18th July 2018, 08:42 PM #36GOLD MEMBER
- Join Date
- Apr 2018
- Location
- Nsw
- Age
- 64
- Posts
- 1,361
-
20th July 2018, 11:04 PM #37Senior Member
- Join Date
- Mar 2006
- Location
- West Chermside
- Posts
- 119
I am not a sound engineer but have lined an A frame Titan shed with with R3.5 bats and 19mm ply on the A frame ends so that I could remove the short braces. The walls were lined with R3.5 bats and 16mm ply and the ceiling with R3.5 bats and 17mm ply. I have also lined the swinging doors with R3.5 bats and a 9mm sheet inside. The shed has a main area and then a narrow room across the back where I have a dust extractor and cyclone. The hoses go through the wall by way of shutter gates. If I have the extractor going and the doors are closed I have to concentrate to hear it running and it is only 2-3 meters away on the other side of the wall. This has resulted in a "shed like appearance" with your situation you could probably get similar results with the thick sound insulating type of plaster board and it would look a lot better attached to a dwelling. The only advantage of ply is I can put things anywhere on the walls. I understand there is a product that you can have sprayed on your roller doors that is sound deadening. As for echo I found that coating the concrete floor with a couple of layers of epoxy helped.if it were really an issue you could use waffle foam tiles on areas of one or two walls. . In eateries where they are used you can hear a conversation where previously you only heard all the reflected sound. I can use any tool except the planner with the sound not intrusive in the house. The problem with the planer is I need to open the roller door to feed the timber out the door when using the planer and when in thicknesses mode I feed the timber from the other end. Hope this helps. All the best.
I only just spotted the pic of your ute fall of MDF, which makes most of the above redundant. post a finished pic of the project.
Similar Threads
-
Sound insulation for garden shed setup
By wwf9984 in forum DUST EXTRACTIONReplies: 11Last Post: 31st December 2015, 01:10 AM -
Sound Insulation
By John Samuel in forum DUST EXTRACTIONReplies: 67Last Post: 6th December 2013, 08:24 PM -
Shed Insulation and sound proofing
By Goldy in forum WOODWORK - GENERALReplies: 9Last Post: 13th August 2004, 08:01 PM