Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: Reclaimed Timber Canoe
-
20th June 2013, 02:03 PM #1Intermediate Member
- Join Date
- Aug 2011
- Location
- Hobart
- Posts
- 41
Reclaimed Timber Canoe
I'm toying with the idea of building a wooden canoe. Based in Tassie there is no shortage of premium quality timber celery top/huon pine) but my budget won't allow for this at the moment.
I buy a lot of timber from my local 'tip shops' and was always curious if old tas oak wall studs and floor joists could be used if cut into strips? I like the idea of building a canoe out of reclaimed timber.
I have a table saw and if all goes according to plan will have a 6" jointer/planer and a 13" thicknesser come next weekend.
Any thoughts/feedback or advice would be appreciated.
Cheers,
Paul
-
20th June 2013 02:03 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
20th June 2013, 03:39 PM #2
G'day Paul
Certainly could be done, but any canoe made from hardwood will be heavier than it should be.
Heavy to car-top.
Heavy to carry between car & water.
Heavy to push around on the water.
Every extra kg is an extra kg of water you have to displace & return for every boat length you travel.
For ever, and ever.
Now, if you could reclaim some celery-top floor boards or the like...
Another possibility might be to get some paulonia - light & cheaper than many alternatives.
cheers
Alan JAlan J
Nothing says "Unprofessional Job" so loudly as wrinkles in the duct tape. - B.Spencer
-
20th June 2013, 06:29 PM #3
If you are planning the normal strip built construction process, then you don't need to be concerned about the strength of the timber, but you do need to be concerned about the weight. Tas Oak is much too heavy for the reasons already explained. The strength is in the fibreglass on both sides of the timber.
I have built several kayaks using Paulownia, but I have also used quite a bit of recycled, often free timber.
The deck of the kayak I made for my son-in-law was made from the WRC lining boards I pulled off his bathroom wall when I helped him renovate. I am almost finished a child's racing kayak made from free reject venetian blind slats, although they would be a bit thin for an adult sized canoe. I have also used free Redwood skirting boards and very cheap scraps trimmed from large WRC boards. I have some WRC lining boards salvaged from a kitchen being renovated by the neighbour of a friend of a friend that will be part of a kayak one day.
I like the idea of using free and recycled timber, but you should look for something quite light.
-
20th June 2013, 11:48 PM #4Intermediate Member
- Join Date
- Aug 2011
- Location
- Hobart
- Posts
- 41
Thanks for the responses guys.
I was initially interested in using Tas. Oak because I can pick up truck loads of wall studs and beams etc for next to nothing.
I've been grabbing WRC and Oregon whenever I spot it. The collection is slowly building but I don't have anything over 2metres in length.
I do have some Celery Top boards but they are only 900mm in length. There's about 40metres of them but obviously not enough for a canoe.
Looks like this will become an even longer long term project.
Thanks again!
Paul
-
21st June 2013, 08:36 AM #5
Don't assume that you need strips as long as the canoe. Scarfing is quick and easy and can be quite neat. I find it less of a problem than trying to handle long strips and trying to get them held in place before the glue begins to dry.
My 5 metre kayak is made from 1.8 metre strips and no-one has ever noticed how many joins there are in the strips.
I just sand the ends by leaning the strip at an angle against a belt sander and glue them together on the forms.
-
2nd July 2013, 08:36 AM #6
With typical strip planked building methods (there's about a dozen different ones) you don't need to scarf the strips together. A butt joint will be fine, though I admit to cutting the butt joints at a 45 degree angle to help align them.
Similar Threads
-
Uses for reclaimed timber piles?
By Tippy78 in forum TIMBERReplies: 5Last Post: 3rd October 2012, 08:15 PM -
Reclaimed timber - American style
By Woodwould in forum SMALL TIMBER MILLINGReplies: 2Last Post: 16th December 2011, 05:19 AM -
Can anyone Assess this Timber by looking at a pic? Are you a guru of reclaimed Timber
By jkd87 in forum TIMBERReplies: 10Last Post: 29th July 2011, 07:24 PM -
Difference between recycled & reclaimed timber
By hsc07ww in forum TIMBERReplies: 2Last Post: 13th January 2007, 11:54 PM -
reclaimed timber (we call it wood) lol
By cranbrook2 in forum WOODWORK PICSReplies: 4Last Post: 19th February 2006, 10:10 AM