Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 7 of 7
  1. #1
    Join Date
    Aug 2005
    Location
    Victoria
    Posts
    664

    Default Testing Resistance

    I am having some issues with my van (1984 Hiace) and the alternator is overcharging. The alternator itself has been replaced but the issue persists. It has an external regulator which I have removed and tested in accordance with the manual. It would appear that it is shot but I want to confirm that I a testing it correctly.

    I have a couple of multi meters and the only thing I ever use the resistance function for is for buzzing out cables and testing continuity. The dial has seven settings for Ohms but I am not sure which one I should be starting on. The dial is labelled 200,2k,20k,200k,2000k,20m and 2000m. The manual says for one pair of wires for instance that their should be an infinite reading and then if the contacts are closed it should be 100 ohms. In this instance should I be starting on the 200 range? What if I don't know what reading to expect, then what would I start on? If there is an infinite reading, does that mean it is open circuit?

    Tools

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Aug 2005
    Location
    Victoria
    Posts
    664

    Default

    The regulator has two coils in it. One is nice and copper coloured, the other has some small areas that have lost the copper colour and are more silver. Could this be indicative that the coil is shot?

    Tools

  4. #3
    Join Date
    Aug 2005
    Location
    Victoria
    Posts
    664

    Default

    If I check for continuity on each coil, the copper coloured one buzzws out, the one that has lost some colour doesn't. Is this a reliable approach to testing the coil?

    Tools

  5. #4
    Join Date
    Apr 2014
    Location
    Little River
    Age
    77
    Posts
    1,205

    Default

    It doesn't matter what scale you start on. Place the probes on the coil and adjust the scale until the reading is near the middle of the scale to get the most accurate reading. A reading of infinity is an open circuit and for a coil means it's dead. Any other reading could be affected by poor contacts, shorted turns or some other fault so you need to know what it should be before you can declare it as good.

  6. #5
    Join Date
    Aug 2005
    Location
    Victoria
    Posts
    664

    Default

    Thanks Bohdan. It seems that my voltage regulator is shagged so I have ordered a new one to pick up tomorrow.

    Tools

  7. #6
    Join Date
    Aug 2005
    Location
    Victoria
    Posts
    664

    Default

    Slipped the new regulator in this afternoon and the charge light has now gone out. Need to check the voltage tomorrow but I suspect all is now good. The new regulator is one of those fancy new fangled solid state electronic bits of kit, nothing like the old points type that it has replaced...

    Tools

  8. #7
    Join Date
    Aug 2005
    Location
    Victoria
    Posts
    664

    Default

    13.9 - 14.0V at the battery terminals . Case closed !

    Tools

Similar Threads

  1. Resistance was futile.
    By ozwinner in forum TIMBER
    Replies: 7
    Last Post: 12th March 2006, 06:02 PM
  2. UV resistance of plastic?
    By journeyman Mick in forum NOTHING AT ALL TO DO WITH WOODWORK
    Replies: 3
    Last Post: 24th September 2004, 01:08 AM
  3. Collective IQ. required. Resistance is futile
    By Ben from Vic. in forum WOODWORK - GENERAL
    Replies: 13
    Last Post: 15th March 2004, 09:21 AM
  4. Finishing for moisture resistance
    By wcarey in forum FINISHING
    Replies: 1
    Last Post: 11th December 2002, 06:56 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •