Page 5 of 7 FirstFirst 1234567 LastLast
Results 61 to 75 of 95
  1. #61
    Join Date
    Nov 2011
    Location
    Port Sephens NSW Southside
    Posts
    81

    Default

    Brett,
    Looking good, but there's one problem. Using copper wire to tie the gal mesh together is going to cause corrosion between the dissimilar metal.

    Copper and Brass If an installation requires contact between galvanized materials and copper or brass in a moist or humid environment, rapid corrosion of the zinc may occur. Even runoff water from copper or brass surfaces can contain enough dissolved copper to cause rapid corrosion. If the use of copper or brass in contact with galvanized items is unavoidable, precautions should be taken to prevent electrical contact between the two metals. Joint faces should be insulated with non-conducting gaskets; connections should be made with insulating, grommet-type fasteners. The design should ensure water is not recirculated and water flows from the galvanized surface towards the copper or brass surface and not the reverse.
    Source, https://www.galvanizeit.org/hot-dip-...h-other-metals

    JohnQ

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #62
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,648

    Default

    I had a nagging doubt about that the other day John, and was wondering what the situation might be. I think I saw a pliers-like gizmo in the hardware that looks like it seals a gal loop around wire. Better check it out.....
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  4. #63
    Join Date
    Nov 2011
    Location
    Port Sephens NSW Southside
    Posts
    81

    Default

    Just had look at the big green shed, 1000 Jambro rings $25, ring gun $80. Also known as Hog Rings.

    Good luck with the rings if you use them. Hopefully no more sore fingers.

    JohnQ
    Last edited by JohnQ; 11th December 2016 at 08:57 PM. Reason: Added more

  5. #64
    Join Date
    Jun 2005
    Location
    Helensburgh
    Posts
    7,696

    Default

    Brett, I have tie wire pliers and heaps of gal tie wire if you want and it is a pretty quick process after you get the hang of it.
    CHRIS

  6. #65
    Join Date
    Nov 2006
    Location
    Rockhampton
    Age
    62
    Posts
    2,236

    Default

    Quote Originally Posted by FenceFurniture View Post
    I had a nagging doubt about that the other day John, and was wondering what the situation might be. I think I saw a pliers-like gizmo in the hardware that looks like it seals a gal loop around wire. Better check it out.....
    Wire netting clips are what you want, look like a capital C, there is a couple of sizes, put one clip into the pliers and squeeze closed.


    Pete

  7. #66
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,648

    Default

    Looks like these are what you mean Pete:
    https://www.bunnings.com.au/whites-w...clips_p3040886

    and this shows the clips a little better:
    https://www.bunnings.com.au/whites-w...-pack_p3040887


    I can't be certain, but there seems to be some concern about Stainless Steel in contact with gal, but it seems to depend on the surface area. None of what I read gives a definite conclusion.

    However, those Whites SS clips are designed for their own Bird Wire, so one can hopefully presume that they are ok.

    It certainly looks like a fairly quick process.
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  8. #67
    crowie's Avatar
    crowie is online now Life's Good, Enjoy each new day & try to encourage
    Join Date
    Dec 2009
    Location
    Faulconbridge, Lower Blue Mountains
    Age
    68
    Posts
    11,164

  9. #68
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,648

    Default

    Thanks crowie, but I think I'll invest in the flat type - sadly this won't be the last bird wiring that I'll do (chookies). What's the bet that Bunnings Valley Heights don't stock them and I have to go to Penrith....
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  10. #69
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,648

    Default

    Quote Originally Posted by FenceFurniture View Post
    What's the bet that Bunnings Valley Heights don't stock them and I have to go to Penrith....
    Ah yup, they don't stock them at Valley Heights. Although they did actually have one - sans bonus clips - and they didn't have any extra packs of clips. Apparently this one must have been a return from another store.

    So, to Penrith and back, and they work really well - in the order of 15-20 times quicker than pushing copper wire through holes too small for fingers......wish I'd done some research.....

    I got the bird wire at Masters 3 months ago (the day after they went on sale) and the copper wire was right next to it so I assumed that was the stuff to use.

    Big thanks to JohnQ for spotting the problem.

    I have replaced one wall, and removed the copper wire. There was indeed evidence of corrosion already, and that wall has only been done for 10 days.
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  11. #70
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,648

    Default

    Quote Originally Posted by Chris Parks View Post
    Brett, I have tie wire pliers and heaps of gal tie wire if you want and it is a pretty quick process after you get the hang of it.
    Funnily enough I discovered a roll of gal tie wire in the garden shed yesterday, during a routine tidy up. It would have been left by a previous occupant (I'd have remembered it if it was something I put in there). I will have to use some of this to attach the birdwire to the weldmesh, as the J clips aren't quite big enough. I don't have proper pliers, but a normal pair will do for the small number of these ties, or maybe a careful grab with the end-cutters.
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  12. #71
    Join Date
    Nov 2007
    Location
    Albury Well Just Outside
    Posts
    13,315

    Default

    Quote Originally Posted by fletty View Post
    There's a Summer in Katoomba ?

    Yes..... There is......

    If you blink you will miss it.

  13. #72
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,648

    Default

    Quote Originally Posted by fletty View Post
    There's a Summer in Katoomba ?
    Yep, Christos is right - it's shorter than most - and a WHOLE lot more pleasant (although still 30°) than it is in Camden today and tomorrow......
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  14. #73
    Join Date
    May 2007
    Location
    North of the coathanger, Sydney
    Age
    68
    Posts
    9,417

    Default

    hmm, I probably should have given you some pointers on the fine art of affixing this sort of stuff. I was a fencer in a former life
    regards
    Nick
    veni, vidi,
    tornavi
    Without wood it's just ...

  15. #74
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,648

    Default

    On Saturday I did the plumbing inside the garden, using Pex Pipe and Sharkbite fittings. It's a really easy (but not cheap) system to use. Just push the fitting on (about 25mm) and it's done. DaveTTC put me onto it.



    You can see the pipe which has to be to be joined onto more pipe which is currently only to the back of the shed. Waiting on a retaining wall to be built so I can do that, but I may have to do a temporary job so I can use the water (very keen to sow some seed for what is left of the season).


    That was the penultimate task. The very last is to make the rolling gates. Here it is during a test fitting yesterday (sorry 'bout the sideways - I tried):



    I'm using Unistrut channels and wheels for this. Very good quality but REALLY expensive. $120 for 6m of channel, and $200 all up for the two gates.....which makes them about $175 for each gate with timber, birdwire, paint etc.

    Big shout of thanks to fletty for picking up the Unistrut from near his home and delivering it last week.


    So of course, at that sort of money I wanted to absolutely minimise the amount of channel required. This involved more thinking than I had reckoned on

    The position of the wheels (distance from the gate edge) is quite critical, as is the positioning of the lower channel, as are the lengths of the pieces etc. An Excel doagram provided the answers (and I had to give fletty the cutting lengths before he could pu - 6m of channel on the roof is a bad idea).

    The top channel is almost twice the length of the gate



    A Channel Nut on each end stops the gate from rolling off. Much planning went into calculating the exact positioning of the wheels and the channel length, but as it turns out, the big square washer is what the wheel housing hits up against




    I didn't use the roller wheels for the bottom because that would have meant another lenght of channel. Instead, I've been able to get away with a very short piece and a guide board attached to the bottom of the gate. Those pieces of H4 pine have had a couple of licks of creosote, as they are now buried in soil.



    The guide board on the bottom is Merbau (nice and easy to find and retrieve from the new woodstore shed ) which has very good life outdoors in my experience, but again it got a couple of licks of creo.



    The pale grey that you can see is Sikaflex which I used liberally in the half-lap joints of the gate (8 of them). It is particularly good at sealing end grain from the elements, and it readily accepts a paint finish.
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

  16. #75
    FenceFurniture's Avatar
    FenceFurniture is offline The prize lies beneath - hidden in full view
    Join Date
    Oct 2010
    Location
    1017m up in Katoomba, NSW
    Posts
    10,648

    Default

    And the final result.




    Had a few brass handles hanging around.



    The handle for the inside has to slide past the post, so needs a concealed position.



    So, one more gate to make, connect the middle bit of the plumbing, and it's complete!

    Just talking to DaveTTC a few minutes ago and he asked me how I made the joints ("half-lap"). He was curious as to how a floating tenon would compare for strength and durability. I may just make the second gate with floating tenons for a giggle, and a vast time saving, so Dave, I'll get back to you in about 10 years on the answer to that

    I don't actually have any "outdoor" dominoes but if I use Sika instead of glue they should be fine - if water can't get in there should be no problem with durability/rot - let's see.
    Regards, FenceFurniture

    COLT DRILLS GROUP BUY
    Jan-Feb 2019 Click to send me an email

Page 5 of 7 FirstFirst 1234567 LastLast

Similar Threads

  1. Vege & Fruit shelf (First project)
    By johnjohnmulley in forum WOODWORK PICS
    Replies: 11
    Last Post: 2nd March 2009, 11:17 PM
  2. raised vege garden
    By Liz5264 in forum LANDSCAPING, GARDENING, OUTDOORS
    Replies: 15
    Last Post: 22nd April 2008, 04:55 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •