Page 1 of 2 12 LastLast
Results 1 to 15 of 17
  1. #1
    Join Date
    May 2016
    Location
    Blue Mountains, Australia
    Posts
    462

    Default Paulco 12" Bandsaw restoration (Paulcall)

    In my recent Wanted thread ( Bandsaw (something cheap 'n dirty) ) I described my acquisition of a 1940s/50s 12" Paulco Bandsaw. Here I'll briefly outline my quick restoration.

    paulco01.jpgpaulco02.jpgpaulco03.jpgpaulco05.jpg

    Firstly, Paulco was a brand name used by Paul's Pty Ltd hardware merchants in Sydney and Australia wide. This bandsaw is identical to Paul's other more well-known machinery brand name Paulcall. (Both brands were registered in 1948. ) The only difference between my Paulco 12" and Paulcall 12" bandsaws appears to be the blade guides (however mine may just be non-original guides as the 1950 Paulco advertising illustration posted below has the same elongated styled Paulcall guides) .
    And later Paulcall's have solid aluminium wheels.

    I suspect the Paulcall branded 12" bandsaw is slightly later in production. I even found under the battleship grey repaint the same blue-green (turquoise?) paint colour.

    paulco04a.jpg

    NCArcher's thread ( Paulcall Bandsaw ) about his 12" Paulcall has been very illustrative and helpful in comparing the two Paul's branded bandsaws.

    Cleaning and wire wheeling the guides and parts was fiddly but without dramas. As was the tilting table which seemed to have endless rust in its surface.

    paulco04.jpgpaulco09.jpgpaulco08.jpgpaulco10.jpg

    I don't usually repaint tools/machinery but this time it just seemed appropriate. Dulux Metalshield Enamel Epoxy. Not any better than the Whiteknight Rustguard Enamel Epoxy. Hopeless quality really but it'll just have to do I suppose.

    paulco07.jpg


    It also required new urethane tyres from Sulphur Grove c/o Woodworking Tools Australia - The Woodkid (great service! )
    The upper wheel had been replaced somewhere down the line and was acceptable but the lower wheel tyre was very cracked and quite distorted from sitting under tension.

    paulco11.jpg


    I considered replacing the ball bearings but really they are fine with just cleaning and regreasing.

    paulco06.jpg


    The single phase 1/2hp Hoover motor I might switch out if it can't handle the harder timbers. It only required a clean out and I have enclosed it and its new wiring and switch in a simple box.


    The rough steel and hardwood stand was easily repainted, sanded and oiled and polyed and given new feet.


    The door cover required a few dents removed and got treated to no less than a primer, two coats of enamel then after a change of heart, light sanding and another two coats of paint. I think I've spent almost the bloidy price of the machine on paint!


    Finally it is finished and I can just finish enclosing the pulleys and get on with using it!
    It cuts very true and has pretty of grunt. Gidgee is a heavy slog but a new blade will help I think before I consider more HP.

    Vaughan

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    May 2016
    Location
    Blue Mountains, Australia
    Posts
    462

  4. #3
    Join Date
    Dec 2013
    Location
    Sydney
    Posts
    139

    Default

    Very nice restoration Vaughan !

    I know what you mean when you talk about spending more on paint than on the machine itself. That has happened to me on quite a few machine restorations.

    Where did you purchase the urethane tyres? Why do you say the Metalshield paint was hopeless?

    Graham.

  5. #4
    Join Date
    May 2016
    Location
    Blue Mountains, Australia
    Posts
    462

    Default

    Thanks!

    The urethane tyres are made by the US company Sulphur Grove Tools and sold locally by The Woodkid
    https://thewoodkid.com.au/shop/urethane-bandsaw-tyres/
    I can definitely recommend them - good price, fast service.

    After being disappointed by the Bunnings Whiteknight Rustguard Epoxy Enamel range (poor consistency, very poor drying times, inaccurate recoating advice) on previous projects, I was really hoping that a two part (primer & 2x topcoat) Dulux epoxy enamel option would be far superior and worth the extra time, energy and money but the exact same problems reared their heads.

    Next time I will just use the Rustguard if only for convenience sake. Although I suspect I'm asking too much from a consumer spray paint.

  6. #5
    Join Date
    Dec 2013
    Location
    Sydney
    Posts
    139

    Default

    Thanks for the link to the tyres.

    So you're using spray cans?

    I've used the Whiteknight epoxy enamels, either thinned and brushed on, or sprayed through a HVLP gun, and had great success. You do need to allow very generous drying times and re-coat times, especially in winter.

    Graham.

  7. #6
    Join Date
    May 2016
    Location
    Blue Mountains, Australia
    Posts
    462

    Default

    Sorry about the poor filming (I really should know better!)


    Before


    After

  8. #7
    Join Date
    Apr 2015
    Location
    Brisbane
    Posts
    304

    Default

    I have a Paul Call bandsaw that was my fathers. Great to see your restoration. He bought it second hand in the 60s.
    I used Carter urethane tyres purchased from Gregory Machinery in Brisbane.

  9. #8
    Join Date
    Sep 2021
    Location
    Orange, NSW
    Age
    63
    Posts
    9

    Default

    Vaughan,
    I have a 12" Paulco bandsaw also. It was purchased new by my late uncle Bill Hick who was a boatbuilder, woodworker and eventually building inspector in the Shire. It would have been purchased in Sydney in the 40-50s. He also gave me all his chisels, planes and marking out tools which I have restored and sharpened to razor sharp edges.
    I have chipped off all the hardened rubber bandsaw tyres and replaced them with eurothane from Woodworking Cutting Tools - Accessories - FOXBC. I have purchased a couple of new blades and after inspecting the fairly primative gaurds, am looking at a 3 bearing guide for top and bottom through Timbercon. As the post is 5/8", I will need to either make a shim from 5/8" to 22mm, of drill out the post hole to 22mm and use a new post. The table is rusted firm at the moment. Next job.

  10. #9
    Join Date
    May 2016
    Location
    Blue Mountains, Australia
    Posts
    462

    Default

    Hi Stephen,
    Replacing the post by drilling out the receiver to 22mm sounds like the best plan if you're game.
    I'm tempted to do the same thing The original guides are quite archaic for attempting precision work.
    They are great machines though - solid little units.
    I'd love to see some before-and-after photos of your restoration as you progress.
    V

  11. #10
    Join Date
    Sep 2021
    Location
    Orange, NSW
    Age
    63
    Posts
    9

    Default

    I would if I could. Plenty of photos here. Spent 1 1/2 hrs last night and no joy. Got to be some simple way to do it. Keep submitting.

  12. #11
    Join Date
    Sep 2021
    Location
    Orange, NSW
    Age
    63
    Posts
    9

    Default

    All painted today. 2nd coat tomorrow and then to start on my mystery bandsaw. Eurothane tires are nice. Lower guard seems too tight. Brass adjustment hits the frame. I will most likely have to fabricate something to adapt Timbercon lower guide.

  13. #12
    Join Date
    May 2016
    Location
    Blue Mountains, Australia
    Posts
    462

    Default

    Stephen, there is a minimum number of posts allowed before attachments (photos, videos etc.) are permitted by new members. 5 or 6 from memory.
    So maybe try attaching/uploading a few photos again now?

    V

  14. #13
    Join Date
    Sep 2021
    Location
    Orange, NSW
    Age
    63
    Posts
    9

    Default Photos of Paulco 12" restoration

    Well I have photos, but each photo, placed individually, ends up on it's side, so I will hang on to them until I can figure out how to rotate photos. In the meantime, here is a link to my google drive folder. Who knows, it might work. I also have a video of it running with one top guide in. Seems to run and cut well.

    Bandsaw restoration - Google Drive

    Steve
    Attached Images Attached Images

  15. #14
    Join Date
    Sep 2021
    Location
    Orange, NSW
    Age
    63
    Posts
    9

    Default Blade length

    What length is the blade? I thought I carefully measured then sent away for 2 blades to be made, and they are just too long. I would like your size just to confirm before i get them resized.

    Steve

  16. #15
    Join Date
    Apr 2015
    Location
    Brisbane
    Posts
    304

    Default Paulco 12" Bandsaw restoration (Paulcall)

    I got 1880mm blades for my Paulcall 12”. No idea if Paulco is the same.

    The urethane tyres are thinner than the original rubber tyres so these blades are shorter than the originals.

    Great you can get your blades shortened. Better that having blades too short

Page 1 of 2 12 LastLast

Similar Threads

  1. Jeffwood 27" bandsaw restoration
    By 2blast67 in forum ANTIQUE AND COLLECTABLE TOOLS
    Replies: 39
    Last Post: 5th August 2021, 11:10 PM
  2. N.S.W. G Clamps. Dawn, Carter, Paulcall 8" and 6"
    By aaa in forum WOODWORK - Tools & Machinery
    Replies: 1
    Last Post: 11th June 2018, 06:34 PM
  3. Woodfast 14" Bandsaw Restoration
    By thumbsucker in forum ANTIQUE AND COLLECTABLE TOOLS
    Replies: 24
    Last Post: 13th May 2017, 07:33 PM
  4. Paulcall bandsaw
    By mgwood in forum BANDSAWS
    Replies: 4
    Last Post: 18th April 2016, 10:15 PM
  5. Replies: 22
    Last Post: 22nd October 2012, 10:30 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •