Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Mc1100 lathe help
-
15th July 2017, 07:33 PM #1
Senior Member
- Join Date
- Jan 2008
- Location
- Sydney
- Posts
- 244
Mc1100 lathe help
I'm replacing the pulleys on my mc1100 lathe. I have encountered a problem. The flange on the spindle pulley that sits in the bearing has snapped off in the bearing. I can't for the life of me work out how to get it out. Any help would be much appreciated
Sharp is Best!
-
15th July 2017 07:33 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th July 2017, 07:36 PM #2
Woodworking mechanic
- Join Date
- Jan 2014
- Location
- Sydney Upper North Shore
- Posts
- 4,470
Can you post a picture or a diagram? Is this the diagram? If so, in which bearing is the shaft broken and can you get the what's left of the shaft and bearing into your hand.
IMG_0284.jpg
-
15th July 2017, 09:12 PM #3
Senior Member
- Join Date
- Jan 2008
- Location
- Sydney
- Posts
- 244
Yep that's the one. Pulley 9 is broken in bearing 11. Yes I can get a hold of it.
-
15th July 2017, 09:47 PM #4
Woodworking mechanic
- Join Date
- Jan 2014
- Location
- Sydney Upper North Shore
- Posts
- 4,470
So it's not shaft 33 thats goes through bearing 11 that's snapped?
-
15th July 2017, 09:53 PM #5
Senior Member
- Join Date
- Jan 2008
- Location
- Sydney
- Posts
- 244
No it's the back part of the pulley itself. It slides over the shaft and sits inside the bearing . I'm not sure how to put up a photo from my phone either unfortunately.. I've removed most other parts around it and tried levering, hitting etc. was thinking maybe heat? Or maybe just drill it out
-
15th July 2017, 10:09 PM #6
Woodworking mechanic
- Join Date
- Jan 2014
- Location
- Sydney Upper North Shore
- Posts
- 4,470
It looks like bearing 11 is held inside item 12 by 2 circlips. So the broken part of the pulley is inside the bearing? As long as there's no circlips (c clips) holding the broken part in the bearing it should press out. Where abouts in Sydney are you?
-
15th July 2017, 10:48 PM #7
Senior Member
- Join Date
- Jan 2008
- Location
- Sydney
- Posts
- 244
Campbelltown mate a bit far from you. I've gotten the front circlip off. I saw the one on the back. Had a bit of a go at it. May be worth another look. Thanks for your thoughts mate I'll keep you posted
-
23rd July 2017, 09:32 PM #8
Senior Member
- Join Date
- Jan 2008
- Location
- Sydney
- Posts
- 244
Back on! I drilled it out and got the new one on and we are away. So happy 👍
Last edited by ficfac; 23rd July 2017 at 09:32 PM. Reason: Spelling
Reply With QuoteSimilar Threads
-
MC1100 Lathe Cabinet/Bench with storage
By Robomanic in forum WOODTURNING - GENERALReplies: 43Last Post: 23rd July 2011, 10:04 PM -
Jepson MC1100 Wood Lathe Switch
By Silly Sandra in forum WOODTURNING - GENERALReplies: 11Last Post: 19th December 2010, 10:02 PM -
MC1100 lathe motor problems
By GC in forum WOODTURNING - GENERALReplies: 2Last Post: 7th December 2006, 04:55 PM
