Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 3 of 3
-
3rd May 2008, 01:35 PM #1
New Member
- Join Date
- May 2008
- Location
- West Aust
- Posts
- 2
Removing/replacing Bathroom Vanity Please Help?
Not sure where to start as I am new at this. We have removed the vanity from bathroom. The old one - the top was rounded up at the back where it attached to wall and met the existing tiles . Now that its removed there is a gap we will naturally fill, new tiles etc. BUT the new unit - when its fitting over the drain its is about 3 to 4cm out from actual wall and also has 2cm gap on each side where you can see the existing hole in the wall 'bricks etc, which were originally hidden with older vanity - bit aware of using timber to fill the gap - for the dampness factor'. Help! Its the top of the unit gap between the edge at the back and the wall that concerns us 'do we cement the existing actual gap in the wall in around the pipes and start with a flat wall surface? We are aware the gap at the top can be covered with tiles etc, but do we fill the total hole in at the back, just cover the gaps at the sides and then tackle the top - assuming by now we have cemented the total gap up to within a couple of cm's within the top of the back of the unit - allowing us to tile, seal etc.....
Thanks Guys
chattyj
-
3rd May 2008 01:35 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
3rd May 2008, 06:58 PM #2
Senior Member
- Join Date
- Jul 2004
- Location
- ipswich Queensland (Gods backyard)
- Age
- 69
- Posts
- 337
sounds like you should go to a plumbing supplier and buy fittings to suit the waste from the vanity to the floor before you go and get all worked up about the gaps behind the vanity to the wall, pvc is a wonderful product
-
14th May 2008, 12:47 PM #3
SENIOR MEMBER
- Join Date
- Dec 2004
- Location
- Up North
- Posts
- 1,799
1) If I understand you right, then the hole in the cabinet when sitting at the wall does not fit over the drain pipe, right?
Originally Posted by chattyj
Not sure where to start as I am new at this. BUT the new unit - when its fitting over the drain its is about 3 to 4cm out from actual wall and also has 2cm gap on each side where you can see the existing hole in the wall 'bricks etc, which were originally hidden with older vanity -..... Thanks Guys
chattyj
Go to the hardware store and buy an adjustable fitting, looks a bit like the curls on a trumpet
. There are 3 parts that move independently of each other and will connect the basin perfectly with the drain.
The horizontal pipe is for connecting a double sink and you do not need that part.
2) Is the new cabinet narrower than the old one as in width not depth?
Sounds like you have bare wall showing with, perhaps, holes in it?
Before you fit the cabinet, cover the bare wall with cement sheet (Hardiflex) and then do whatever looks good on the visible part once you have fitted the cabinet, if it is only 20mm on either side, paint it the same colour as either the cabinet or the wall/tiles.
WolffieEvery day is better than yesterday
Cheers
SAISAY
Similar Threads
-
Bathroom Vanity finishes
By paulalbe in forum FINISHINGReplies: 1Last Post: 8th March 2007, 02:10 PM -
Bathroom Vanity
By johnc in forum WOODWORK PICSReplies: 6Last Post: 16th April 2006, 11:30 PM -
Bathroom vanity top
By growl in forum FINISHINGReplies: 2Last Post: 1st November 2005, 01:36 PM -
Bathroom Vanity
By trevorZ in forum WOODWORK PICSReplies: 6Last Post: 26th October 2004, 01:32 PM
