Needs Pictures: 0
Results 1 to 13 of 13
Thread: Pink Gum table
-
2nd August 2016, 06:29 PM #1New Member
- Join Date
- Jul 2016
- Location
- Adelaide
- Posts
- 4
Pink Gum table
Hi all,
I have been working on this table for a few months now. I helped cut this timber about 8 months ago from a tree that had been laying on the ground for a year. It is an old pink gum tree. All the joints are mortised and domino. I used 100mm dominos on the slab joints. 60mm dominos on the surrounding edge skirt. Surrounding edge skirt is jarrah.
Sanding to 400.
The table top has now had a coat of Scandinavian oil. It will need quite a few more yet.
Frame is yet to be made out of jarrah.
-
2nd August 2016 06:29 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd August 2016, 07:18 PM #2GOLD MEMBER
- Join Date
- Dec 2010
- Location
- Mornington Peninsula
- Posts
- 2,746
That looks fantastic. It also looks very heavy.
-
2nd August 2016, 07:56 PM #3Intermediate Member
- Join Date
- Jun 2016
- Location
- Wollongong
- Age
- 66
- Posts
- 43
Wow! Beautiful timber and work.
-
2nd August 2016, 07:59 PM #4
noice
regards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
2nd August 2016, 08:55 PM #5
Now that's a solid job ,worthy of a XL700 approach .I like what what you have done .
CheersJohnno
Everyone has a photographic memory, some just don't have film.
-
3rd August 2016, 10:43 AM #6
-
11th August 2016, 04:47 PM #7
I love the colour on this piece. Not sure about frame on the outside. What are you going to make the legs from?
-
11th August 2016, 05:15 PM #8New Member
- Join Date
- Jul 2016
- Location
- Adelaide
- Posts
- 4
The frame is a necessity really. The rounds were about 60mm thick when fully milled. To avoid any fracturing in the future I put a frame around and underneath the timber. So far this has been successful.
The legs an apron will be made out of jarrah. The outer frame on the table top is also jarrah.
-
11th August 2016, 06:30 PM #9SENIOR MEMBER
- Join Date
- Aug 2013
- Location
- Montmorency Victoria
- Posts
- 554
Perhaps the edging and end boards have floating dominos?
The movement would seem to be both lateral and longitudinal because of the grain directions on the slabs ... big wood plus red gum .. = movement and twisting and needs to be considered in the design so floating tenons are a must IMHO
The table top looks fantastic ... I can readily see the amount of work in preparing the raw timbers ..
This table will be a real heirloom piece for generations.
Regards
Rob
-
22nd August 2016, 11:10 AM #10New Member
- Join Date
- Jul 2016
- Location
- Adelaide
- Posts
- 4
Certainly, my main consideration with framing and use of dominos was to prevent any further movement of the timber. I think the use of a plywood base glued to the slab will prevent any large scale movements. As yet I have not seen any large movement. This table was after all, an experiment and I hope the measures I have taken will allow for prevention of movement. I have now done around 25 coats of oil as I am looking for a particular finish. So far it is looking very good. A few more coats yet and then I will let the finish harden for a few weeks before polishing. Table frame construction is underway. I'll post some images when I get time.
-
22nd August 2016, 04:00 PM #11
Certainly an experiment outside the norm. I think I would have preferred to see the large squarish section centered with the narrower pieces extending to each side.
Cheers, Franklin
-
22nd August 2016, 05:22 PM #12
Hi Phaese
I am going to make a suggestion that I hope you take (as intended) to be constructive. The timber you are using has great potential, which is not being realised.
The effect you have is jarring because the grain is interrupted by the way you have linked the pieces. It has no flow. The two split halves would greatly benefit from facing one another, to resemble the full section (on the left in the photo). Sand down, cut up the top, and re-assemble. Ouch! Sorry.
Secondly, the Jarrah surround would better be (a) in pink gum. (b) Either way, the ends need to be mitred, not butt jointed.
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
22nd August 2016, 11:06 PM #13New Member
- Join Date
- Jul 2016
- Location
- Adelaide
- Posts
- 4
Thanks Franklin and Derek for your observations and thoughts.
It would have been nice to have more material but unfortunately the way I have put the slabs together is the most efficient use of the materials. I take the point about the mitres but have chosen butt joints to limit movement that may occur with the slabs.
For more enjoyment I submit a few more images of the frame being constructed.
Similar Threads
-
Pink builders bog
By Guy M in forum FINISHINGReplies: 19Last Post: 31st March 2016, 07:46 PM -
Pink gum?
By Max250 in forum TIMBERReplies: 0Last Post: 29th May 2015, 05:03 PM -
The Pink Box
By JayTas in forum BOX MAKINGReplies: 12Last Post: 7th September 2014, 08:35 AM -
WW..Pink.
By minus459 in forum WOODTURNING - PEN TURNINGReplies: 10Last Post: 5th August 2011, 01:43 AM -
hot pink?!??
By Tat_freak_2210 in forum MUSICAL INSTRUMENTSReplies: 5Last Post: 1st June 2009, 01:18 AM