Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
-
20th March 2019, 10:52 AM #1GOLD MEMBER
- Join Date
- Nov 2018
- Location
- Newcastle
- Posts
- 1,016
Crosscut sled: Personal recommendations & Tips
I'm going to make a crosscut sled for my new Sawstop.
I'm tending towards something like this one: - a few variations on youtube from peops like Nick Ferry, all very similar with the two t-tracks and the Kreg top Trak.
I'll make the runners out of polyethylene, and have plenty of T-track lying around. May add the top trak later on.
Does anyone who's made a sled have any recommendations for alternate designs, or things you'd have added/done differently?
Screenshot 2019-03-20 10.45.26.jpg
-
20th March 2019 10:52 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
20th March 2019, 06:19 PM #2
Hi Bernmc,
When I was contemplating my first sled I suffered analysis paralysis and took a long time deciding how to build my perfect sled. Then one day I desperately needed a sled for a simple job and knocked one up, and so began the sled collection.
The best advice I can offer is to not overthink it. Spend $24 (or is it $42) at Bunnings on a 2400x1200x17 sheet of mdf, and make a basic sled. Then when you need to do something else, make another one, and so forth. If at some point you think you need a super sled like the one in the video, go for it. Though I'd suspect after your first couple you will consider it far simpler and more practical to have several dedicated sleds for different types of cut.
Oh, and when a family member uses your sled to do a funky angled cut that makes it useless for what you built it for, rather than throwing a fit, you can just shrug and make another one, because it only cost you $5 and 15 minutes to make in the first place. [emoji3]
Lance
-
21st March 2019, 12:15 AM #3GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,330
Three things that are probably fairly obvious :
Make the scale on top of the fence movable, so you can accommodate blades of different thickness (assuming sawstop has such things).
Make the fence fixed on one end but movable on the other, so you can fine tune it to the last tiny part of a degree. I know that if you build it at 90% to the blade it should stay that way but somehow they don’t.
I’d use a blade guard too. I was lucky to find some long strips of Lexan which made perfect blade guards. Just a strip between the front stiffener and the fence, above where the blade travels, and perhaps on the other side of the fence (where the blade emerges as the sled is pushed past the blade).
Also, I thoroughly agree with Lances comment that it’s better to make several sleds for dedicated tasks rather then one excessively complicated one. I had 9 at one stage, which may have been going overboard a bit.Apologies for unnoticed autocomplete errors.
-
21st March 2019, 10:39 AM #4
Lance is giving good advice. Keep it simple. The important bit is getting it cutting at 90*.
Regards
John
-
28th March 2019, 10:26 AM #5
-
31st March 2019, 08:53 AM #6
Whilst I haven't watched the one from King's Woodworking yet, here's the one I had bookmarked and thought of making: https://www.youtube.com/watch?v=KWyLrDZAW-c
Similar Threads
-
Crosscut sled
By John Samuel in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 11Last Post: 13th October 2012, 04:47 PM -
Best crosscut sled I've seen
By I_wanna_Shed in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 7Last Post: 19th September 2011, 11:26 PM -
Crosscut sled - how to
By niki in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 12Last Post: 6th August 2009, 01:45 AM -
Crosscut Sled
By Beagle67 in forum HAND TOOLS - POWEREDReplies: 1Last Post: 18th August 2006, 06:30 PM