Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 6 of 6
Thread: X2 electrical experience??
-
20th August 2015, 08:07 PM #1GOLD MEMBER
- Join Date
- May 2011
- Location
- Murray Bridge SA
- Posts
- 3,339
X2 electrical experience??
Anyone in Adelaide have any experience with the X2 mini mill electrics, and would be prepared to look at it for me PLEASE? Had the circuit board checked, that's OK. The amber fault light is on, when the potent meter is in the run position, but no go in the motor, have replaced the fuse also. Anyone come across this problem?
Thanks in advance.
Kryn
-
20th August 2015 08:07 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
20th August 2015, 09:36 PM #2Member
- Join Date
- Oct 2009
- Location
- Upwey VIC
- Posts
- 95
Kryn,
The amber fault light on mine comes on when the motor is overloaded (drawing high current over it's rating).
Possibly your motor has a short circuit internally, or even has a seized bearing?
Andrew.
-
20th August 2015, 09:49 PM #3GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 2,685
The amber light is controlled by the over-current circuitry - although I can't find an indicator lamp on the circuit diagram.Geoff
The view from home
-
20th August 2015, 10:24 PM #4Cba
- Join Date
- Aug 2007
- Location
- Melbourne
- Age
- 68
- Posts
- 1,417
If the speed control is tested fine, and the overload light comes on, chances are the motor has a problem. Sieg makes their own brushed DC permanent magnet (PM) motors. From my experience with my X3, not the best quality I am afraid. About what you would expect in an Asian kitchen blender or treadmill. Some newer Sieg mills do however have brushless DC motors, if this is your case disregard the following.
It is not difficult to test a brushed PM motor. Take the motor off the mill head. Scrape or punch a line across the brush carrier flange to mark its position relative to the outer frame - should the motor turn out to be ok, you need this to reassemble witout having to worry about proper timing. Remove the brushes if removable (two plastic screw caps). Take out the long screws that clamp both flanges together. Carefully remove the flange with the brush carrier. Inspect visually, if the brushes or brush carriers are damages or extremely dirty, you may already have forund the problem. Else carfully remove the rotor/armature. Try not to have it slide along the magnets (you may insert a cardboard or Brass/Aluminium/plasic strip to prevent this). It may otherwise partially de-magnetize the magnets. Now you can test the armature with an Ohm-meter. Chances are there is a short beteen two windings, or a winding is shorted to ground. These two links explain in detail how to do the testing:
http://www.groschopp.com/how-to-check-a-motor-armature/
https://www.youtube.com/watch?v=qNV7TylIzSY
-
20th August 2015, 11:14 PM #5GOLD MEMBER
- Join Date
- May 2011
- Location
- Murray Bridge SA
- Posts
- 3,339
Hi CBA.
Thanks for the instructions on dismantling the motor and the links, very interesting, will check the motor out tomorrow.
Thanks
Kryn
-
21st August 2015, 06:21 AM #6
Hi Kryn,
Don't make any attempt to remove the armature the magnets will start to loose their strength if you do. Most likely is a brush failure ! or windings have a short in them. Putting the motor across a 12 volt source like a car battery should cause the motor to try to turn. If it turns and tries to lock in one spot then you have a short in the commutator or windings. A brush failure can be easily seen when the brush is removed, the pigtail will be loose in the carbon and you might see signs of local overheating. If you are lucky new brushes should clear the problem.
HTH.Best Regards:
BaronJ.
Similar Threads
-
Work Experience Experience
By brendan stemp in forum WOODTURNING - GENERALReplies: 12Last Post: 14th October 2012, 10:09 AM -
Electrical & CFM
By Chris Parks in forum DUST EXTRACTIONReplies: 11Last Post: 14th June 2009, 12:03 AM -
electrical help
By Harry II in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 22Last Post: 29th October 2006, 08:44 PM