Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
Thread: My very 1st attempt
-
21st June 2009, 06:01 PM #1Member
- Join Date
- Aug 2004
- Location
- Cecil Plains Qld Aus
- Posts
- 61
My very 1st attempt
This is the very 1st pen I have turned and it was a disaster its a Slimline Kit and a Huen Pine blank. I had terrible trouble getting it off the mandrel and ended up cracking the top section. The timber also just sits proud of the bottom part where the pen comes out as I had to wind the nut down the mandrel to get it off and that burred the end of it slightly. I also went a little heavy with the sanding and it got a little out of shape. I sanded to 12000 and finished it off with EEE and 2 coats of shelawax. All in all it was a learning experience. Can anyone help with the problem of getting the off the mandrel
Not a good photo as wife had camera so just used iPhone.
Thanks in advance.He who dies with the most tools wins.
My greatest fear is when I die wifey will sell my tools for what I said I paid for them.
-
21st June 2009 06:01 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
21st June 2009, 06:38 PM #2
Dodgy,
Make sure the inside of the tubes are clear of glue before you put them on the mandrel. I also use a hand held countersink to put a slight bevel on the inside mouth of the tubes and to clean off any rough edges - makes it easier to mount and easier to locate the fittings during assembly.
If they are still a tight fit on the mandrel, try a thin smear of wax on the inside of the tubes.
If they still wont come off reasonably easily (ie with finger pressure),make sure that you apply pressure through the bushings, not directly to the ends of the barrels - they should transfer any pressure you have to exert through to the brass tube, protecting the timber. Slow and gentle is better than a couple of brutal whallops (tempting though that may be at times).
good luck & let's know how #2 goes.
DMCoffee, chocolate, women. Some things are better rich.
-
21st June 2009, 06:53 PM #3
Now you are on your way, give another one a go,maybe use red gum, and pinch the camera off the wife and let us see the next one, you did ok for a first time, keep going, Amos
Good, better, best, never let it rest;
Til your good is better, and your
better, best.
-
21st June 2009, 07:38 PM #4Senior Member
- Join Date
- Oct 2002
- Location
- Doncaster East, Vic, Aus
- Posts
- 146
See the turning pens podcast if you have not already.
It was mentioned in this thread;
https://www.woodworkforums.com/showth...hlight=podcast
#10 reply has a link to the podcast, which is;
http://www.woodworkingonline.com/200...art-to-finish/
Cheers, Steve
-
21st June 2009, 11:52 PM #5
Sounds like your barrel trimmer cut to the brass tubes and left a slight lip or burr in the end, which makes it hard to get the blank on and off the madrel shaft....if you had to "screw" the blank onto the mandrel you formed the burr...its ok to stop the barrel trimmer just shy of flush with the tube when squaring up the end of the blank...just shy means a tiny tiny bit before the brass, you know, have to hold it up to your eyes and squint a little to see it close...and take a hobby knife and clean the glue out of the tube ends, and cut the burr away too, it soft brass and the knife will cut it....countersinking the ends can remove any burr that was formed too.
Ok, so now that you have turned a pen, its about time you started on another one...
Its a learing process, and after many many years, I still am learning...thats why I am here on this forum, lots of minds to listen to.
-
22nd June 2009, 09:37 AM #6
I have a thin round file (called a "bastard"!) for putting twists on my hair sticks. I found that if I had trouble getting pens onto the mandrel I just give a couple of swipes with that and they slid on easily. Usually it's because some glue has got inside and made a little lump. While the little lump is harmless, once it's been spinning on the mandrel it melts and sets TO the mandrel, and that makes it very hard to get it off again.
-
23rd June 2009, 11:20 PM #7
You didn't do too badly for a first attempt and the slimline is not the easiest pen to make. Most folks start off with them because they are reasonably priced kits. You will find the Sierra is an easier pen to make but having said that, making the slimline is great practice and you will learn a lot from making them. keep at it. For a first attempt, you did pretty good.
Reality is no background music.
Cheers John
-
24th June 2009, 07:42 AM #8Member
- Join Date
- Aug 2004
- Location
- Cecil Plains Qld Aus
- Posts
- 61
Thanks for all the tips and kind words I will be turning another this arvo with a bit of luck.
He who dies with the most tools wins.
My greatest fear is when I die wifey will sell my tools for what I said I paid for them.
-
24th June 2009, 08:47 AM #9
Good luck with your second pen.
If I feel that a pen blank is tight going on to the mandrel I spend time then to free it up that way can turn off any marks that may have been made. If the blank went on easy but would not come off easy then I would guess you are tightening your locking nut far to tight and your bank is binding up with your bushes.
Please net us know how your second pen turns out. And keep your first as a reminder where you have come fromCheers Rum Pig
It is easier to ask for forgiveness than permission.
-
24th June 2009, 09:39 AM #10Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Can't give you any better advice than that already given Dodgy but you've mad a start and will quickly learn how to go about things. I have no doubt you work will show rapid improvement.
-
24th June 2009, 09:43 AM #11
The advice given has been good. The only thing I do is I still use the 1/2' trimmer for slim lines and any of the 7mm tubes seems there is no gap between cutter and shaft. I also have a chamfer tool used in reloading of bullets to give the parts a lead in when assembling.
Cheers
Darren
Similar Threads
-
DNF at first attempt
By bigfish in forum WOODTURNING - PEN TURNINGReplies: 3Last Post: 15th September 2008, 11:08 PM -
First Attempt
By DavidW in forum WOODTURNING - PEN TURNINGReplies: 12Last Post: 11th August 2008, 09:25 AM -
First Attempt at a box lid
By lubbing5cherubs in forum WOODTURNING - ORNAMENTAL TURNINGReplies: 5Last Post: 22nd April 2008, 11:47 AM -
1st Box attempt
By Simomatra in forum BOX MAKINGReplies: 15Last Post: 16th June 2006, 08:36 AM -
My first attempt at a pen
By Gra in forum WOODTURNING - PEN TURNINGReplies: 4Last Post: 13th February 2006, 07:47 PM