Thread: trouble with setting the depth

I'm not too sure what you mean by the face and back of the joint. Do you mean the pins are not parrallel? If that is the case i would suggest that the workpieces are moving during the cut. Make sure they are clamped securely to the right angle fixture.
Also make sure the right angle piece is adjusted so that it can slide freely but not move from 90 deg to the fence. Tighten the teflon crews until the RA piece can't move then back the screws off very slightly so that it can slide. Top speed should be ok.for dovetail bits.

Thanx for the info. what i mean about the pin boards is.. at the start of the cut they are just a fraction wider then at the end of the cut. i'm using the same clamping system as in the instruction video.

Can you tell me what you use for a router base? i'm using a product purchased from leeValley here is calgary. The base came with a slight curve to it to account for router weight over time. Does that sound right? at least thats what they are telling me.

That could be contributing to your problem. If your work is rising and falling as you slide it over the router your going to get a drift in the cut.

Router tables should be flat, as flat as possible. If they bow the insert to accomodate router weight the insert in underengineered. This is why my incra insert is solid cast 3/8 inch aluminium. No sag.

I'd be looking at the router plate, I noticed on mine that the insert rings don't quite sit perfectly true with the surface which also has the slightest bow as yours has and it does cause a problem with the work rising and dropping back. Will be replacing it with a new aluminium plate in the very near future, either an Incra or Woodpecker plate.

Originally Posted by DJ's Timber

I'd be looking at the router plate, I noticed on mine that the insert rings don't quite sit perfectly true with the surface which also has the slightest bow as yours has and it does cause a problem with the work rising and dropping back.

An unloaded phenolic plate is designed to have a slight crown so that when a router is fitted the plate will settle in a level plane. Not sure if this is what you are seeing?

I'll be selling an incra al plate at some point. Owes me $128, bough it on special in the US for (I think) $75 when the $ was 95c, the rest was shipping. Now I've bought the table saw I won't need it anymore. Just an option if your looking to buy...

A curved plate is a curved plate. Not good.

Originally Posted by Groggy

An unloaded phenolic plate is designed to have a slight crown so that when a router is fitted the plate will settle in a level plane. Not sure if this is what you are seeing?

I realise that it is designed that way Groggy but if after the router is fitted and it still has a crown, what do you do then plus the fact the the 2 piece ring set that sit in it has a slight step as well is annoying, especially when the timber catches when you're feeding it in

Originally Posted by DJ's Timber

I realise that it is designed that way Groggy but if after the router is fitted and it still has a crown, what do you do then plus the fact the the 2 piece ring set that sit in it has a slight step as well is annoying, especially when the timber catches when you're feeding it in

Didn't mean to tell you to suck eggs DJ .

This is my old unit? It didn't have those issues previously and sat very flat. Unless there is dust or a deformation of the plastic lip there somewhere I can't see why it would have changed

Originally Posted by Groggy

Didn't mean to tell you to suck eggs DJ .

This is my old unit? It didn't have those issues previously and sat very flat. Unless there is dust or a deformation of the plastic lip there somewhere I can't see why it would have changed

None taken

Yes it is your old unit I'm talking about, maybe your router was a bit heavier, might have been that fact that yours had three screwholes rather than four or the fact that it now has two extra sets of holes in it since it has come into my hands which may have buggered it up.

all excel suggestions guys thanx, i've now found a spot on my setup that is consistant and now have made a few very nice dove tails. I will take your advice and look into an incra setup for my router. I'm sure in the long run it will save tons of time. thanks everyone for the quick responses. All the best everyone.

Just get any of the heavy duty inserts, preferably 3/8 thick and aluminium. Whichever is cheap. I ahve to say though the magnalok plate is wonderful. It's going to kill me to sell it.