Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 8 of 8
  1. #1
    Join Date
    May 2008
    Location
    Melbourne
    Posts
    8

    Default Reuse framing timber

    Hi,
    I have a reasonable amount of timber that I collected after removing an internal wall from our 1950s house (we're located in Melbourne). I don't know for sure what type of timber it is, but I expect is a eucalyptus of some sort.
    My question is, can i use this for joists on a deck that will be exposed to outside weather conditions (rain and sun) - assuming the dimensions are correct, or is it likely to start rotting within a short period of time.
    Cheers,
    Luke

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    May 2012
    Location
    Woodstock (Cowra)
    Age
    74
    Posts
    3,372

    Default

    #1 What sectional size is it?
    #2 If you scratch (firmly) the surface with a nail, does it barely mark it or does it leave a distinct groove?
    The person who never made a mistake never made anything

    Cheers
    Ray

  4. #3
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    63
    Posts
    13,354

    Default



    Also: how are they for splits, nail- and/or fixture holes that will collect moisture?

    In the past I have successfully re-used old wall studs for decks, if they were both of a size and in good nick. (Successful in the sense that they've lasted this far without needing further attention.)

    FWIW I also trim malthoid into long 60mm(ish) strips to run along the tops before affixing reeded decking boards. It's the way I was taught, although I've had blokes think I'm odd in the head and am wasting time and money. Still, I'd rather spend $30 "needlessly" on prevention than not do it and have to pull up the deck for repairs... and malthoid is dirt cheap.
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  5. #4
    Join Date
    May 2012
    Location
    Woodstock (Cowra)
    Age
    74
    Posts
    3,372

    Default

    Skew, better product to use now is Protectadeck https://www.bunnings.com.au/our-rang...p/protectadeck
    The person who never made a mistake never made anything

    Cheers
    Ray

  6. #5
    Join Date
    May 2008
    Location
    Melbourne
    Posts
    8

    Default

    Thanks for the replies. I've hopefully answered the questions raised below.

    The timber is 35mm x 95mm although some are closer to 100mm.
    If i run a nail along it it just leaves a surface mark, it doesn't gouge it at all.

    There's not much in the way of splits, but there are a few nail holes where the plaster board was attached. If i was to used this timber, i would probably use the protectadeck product Ray suggested.
    Cherrs,
    Luke

  7. #6
    Join Date
    May 2012
    Location
    Woodstock (Cowra)
    Age
    74
    Posts
    3,372

    Default

    90 x 35 Hwd seasoned spaced 400mm will span 1200 maximum.
    I have run this through a certified structural timber software program and the above result is the maximum allowable spans and spacings.
    The results comply with all current relevant codes and standards. Do not exceed these as you will be liable for any failure and subsequent damage or injury.
    The person who never made a mistake never made anything

    Cheers
    Ray

  8. #7
    Join Date
    May 2008
    Location
    Melbourne
    Posts
    8

    Default

    Thanks Ray, i appreciate your advice

  9. #8
    Join Date
    Feb 2019
    Location
    Sydney
    Age
    35
    Posts
    1

    Default

    Usually, I use such materials for the construction of outbuildings. This is always needed. The easiest way is to take a reliable project as a basis - https://bisonconstructions.com.au/st...one-dairy-shed I liked this option and I made a shed for poultry based on it.

Similar Threads

  1. Reuse Center
    By Scott in forum HINTS & TIPS
    Replies: 4
    Last Post: 12th September 2011, 02:30 PM
  2. timber for framing
    By idle1 in forum BOAT BUILDING / REPAIRING
    Replies: 0
    Last Post: 14th February 2010, 05:21 PM
  3. Can I reuse brass tacks when reupholstering?
    By canado in forum UPHOLSTERY
    Replies: 1
    Last Post: 23rd December 2009, 03:00 PM
  4. Reuse old Rechargable Drill on your Boat
    By Wayne Davy in forum MISC BOAT RELATED STUFF
    Replies: 0
    Last Post: 30th June 2003, 10:58 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •