Thread: Shoddy Owner Builder #1

Move

Moving is out of the question........this place has potential, I got it cheap, and whoever buys it would want a council inspection and I'd have to fix it anyway...

Have a fire and collect the insurance??
Now you know why it was "Cheap"

Looks like whatever you do it'll be painful. :eek:

Mick might be able to suggest something

Although it's a real proper crap job I'd be inclined to leave it alone, unless you're looking for something to do.

From what I see it's supported on the joist, plus a bit on the bearer. It's bolted to the joist so movement other than up or down should be minimal. The bit on the back of the bearer certainly isn't doing much and makes it look as bad as it does.

What sort of load is acting on it? (it certainly isn't built to withstand a cyclone (acutally don't even break wind next to it)

Originally Posted by Fantapantz

and whoever buys it would want a council inspection

Why? You didnt?

Al

We got it $20k under market value from a relative 18 months ago.....And if we didn't get into the market then we would be looking at an extra $100k for the same thing now..........

The reason why I have to fix it up? The councils site plan doesn't have part of the deck or the deck roof or the swimming pool on it....

The 10.5m x 7m shed I want on in the back yard means submitting a site plan......if whoever inspects the shed has any scrupples he's going to ask about the stuff not on the site plan.....Hence...fix it before the council sees it., and before the shed gets going.

If youve already made $120,000 profit from the project my advise and time will cost you $200 per reply.


Al

Hey Oz, at those rates you would have made over $300 grand just for being on this forum...



I reckon I've had my $300k's worth!

Cheers,

P

Fantapantz,

Are the joists secured to bearers properly?

Steel mending plates or gal angle with two bolts each to bearers & post should take care of your concerns.

Since you are getting an engineer to have a look, they can provide expert advice.

OZ, non meat meat – is it tofu ?

Regards,

Theva

Fantapantz,

:eek:


there's three options that I can think of:
1)Leave it alone (if the engineer says it's okay - highly unlikely though)
2)Move the post(s)
3)Move the joist(s)

Depending what the spacing is like (it may or may not be noticeable if your spacings aren't strictly equal) it might be easiest to move the post(s). Take the bottom 600 or so off the post and splice another piece on. You might be able to distract the eye by putting a couple of fancy trims around the post on the joins. It won't hide the half lap completely but it will disguise it.
OR:
Leave the post where it is, move the joist (pain in the @rse as you'll need to get it loose from the decking), and take the bottom of the post off and repair and disguise as above.
OR:
Leave the post, cut the end of the joist off, run a trimmer between the two adjacent joists to support the end of cut joist, run a small trimmer parrallel to rest of joists from 1st trimmer to edge of deck and next to post. New piece spliced onto bottom of post as above.

Check with your engineer, you will probably need to put a pair of splicing plates onto the half lap.

Good Luck!

Mick

Why not grow ivy over it..

Moving the joists a bit shouldn't be a problem cause this guy used a T-nailer, (not galvanised) so most of the nails have rusted off where the floor boards meet the joists.

What about, how the deck posts aren't on top of the main support posts? I thought they had to be directly inline? Do they all have to be moved or can the bearer be reinforced?

(The end of the main support posts is 3m from ground level)

Originally Posted by Fantapantz

......What about, how the deck posts aren't on top of the main support posts? I thought they had to be directly inline? Do they all have to be moved or can the bearer be reinforced?......

This may or may not be a problem. Do the posts take a roof load? If they don't (or the engineer says the bearer can take it without reinforcement AND you can live with the looks) then you can leave it as is. Plans would be really helpful, if there are any but I'm assuming that as it didn't go through council none exist.

Mick