Thread: mini orb in the bathroom

G’day goannadareyou,
We were going to use mini orb but instead went for aluminum checker plate in our shower (no bath). This was a few years ago, so things probably have changed, but I couldn’t find anything that would give a reasonable seal.

The checker plate makes installation a little easier as you can file off the raised areas around the installation points, giving you a flat surface to work against. I even decided against this in the end and went for a ceiling mounted shower rose and a mixer installed outside the showers screen, not much help in your situation but there are always 2 ways to skin a cat.

Just something a little different (it came on the market after I’d finished ours and I’d love to use it) have you seen aluminium propeller plate? not as many raised bits and its chemically polished


Brett

One idea that springs to mind is to get a bit of stainless tube the same size as the flanges on your fittings and use a hole saw to cut a hole the same size for all of your pipe penetrations. Cut a bit of tube so that the flange sits flush with the outside of the tin and push it into the hole around your pipe and then screw on the tap.

Another way would be to use a stainless splash-back behind all of your fittings and put some sort of timber or metal trim around the edge of it and have the tin cut flush to the trim. I think I'd do it that way as it's a straight forward install and I reckon would be easier to keep clean.

goannadareyou
Better late than never , maybe!
I've got the same problem as I'm building our own house and using mini orb in the bathroom. I've been thinking about it for quiet awhile and what I plan to do is use a scrap bit of mini orb, the stuff we used in the bathroom had plastic protective on it, so using a scrap bit of that I peeled it up leaving enough stuck to the mini orb then made a sort of dam or pond about 80mm across and filled it up to about 5mm above the top of the corrugations with Diggers Cast and Embedding Resin. I've removed the cast from the mini orb and it looks pretty good with the corrugations on one side and flat on the other side. Thats as far as I've got at the moment, the next step will be to work out where the center will be and probably using a circle cutter in the bench drill cut out round piece the right size.It may also need sanding a bit thinner.
I was going to use builders bog for the cast and paint it but I had the other resin sitting around and I know I can cut and sand and polish it and it is clear when it sets, which could be another finishing option. There is probably a few different products suitable for the cast. The resin I had came from bunnies. If I get any more done in the next few days I'll keep you posted.

hope I'm not too late - but why run the pipes down behind the mini orb.. a mate of mine has his exposed in his shower and it is really effective. all you need to do is drill through for the securing clamps/rings to hold the pipes in place.

Here is how a bathroom we mini-orbed at the start of this year looks....



We tore off the tiles 7 miniorbed the entire room and then lined it with stained jarrah around the top edge.

Biggest drama was fitting the edges of the sheets together 7 getting enough screws in to hold the mini-orb to the walls properly.

We had no pipe issues as they were already in place & we didn't mive any fixtures (though added a new vanity & got new shower glass).


Cheers,

Aceyducey

And here's a second shot of the room....focused on the vanity (which we made out of a TV cabinet).

Note that the mirror was placed over the mini-orb.

We also inset mini-orb under the bath lip.

Cheers,

Aceyducey

Oh - and here's a 'before' shot of the bathroom

We did quite a bit to it!

Cheers,

Aceyducey

here is a couple of pics of the piece i made to go between the spout and the mini orb which i described earlier. its painted with chrome paint which scratched easily and there is silastic behind it. i still have to make one for the tap

another pic

now i'll rotate the first one

last time

thanks all that replied to this question.

Hi Acey, that bathroom of yours looks really great. well done!
One favour though! We would like to see pic of the edge of your bath especially where you said you inset mini-orb under the bath lip. mmmm. Is this possible?

Thanks again and Merry Christmas to all (unless of course you don't celebrate Christmas in which case enjoy the holiday season anyway)

Alan

Originally posted by goannadareyou
Hi Acey, that bathroom of yours looks really great. well done!
One favour though! We would like to see pic of the edge of your bath especially where you said you inset mini-orb under the bath lip. mmmm. Is this possible?

Alan,

Sorry but don't have a shot of that & the place is tenanted so we can't easily get in to take pics

Cheers,

Aceyducey

Alan

Have a look at the vanity pic and the bath is featured in the mirror.