Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Page 1 of 2 12 LastLast
Results 1 to 15 of 18
  1. #1
    Join Date
    Apr 2005
    Location
    kyogle N.S.W
    Age
    50
    Posts
    4,844

    Default How do you drill holes in tiles without cracking them ?

    Hello,

    I've got 7 holes, about 1" diameter, to drill into tiles.

    I bought a bit specially for the job, but its failing. Or me ?....its one of those things that has a masonary bit (1/4") in the middle of a cyclinder thats lined with diamond dust or something like that.

    I've tried drilling, as lightly as possible, whilst running a trickle of water over it to keep it cool, on cardboard....and still the tiles cracks suddenly, usually near to finish. Frustrating.

    So, its too brittle. Is there any technique that may help ? ...some little thing that may solve this problem ?

    Or, is my only solution to get them professionally drilled ?

    Thanks

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Age
    2010
    Posts
    Many





     
  3. #2
    Join Date
    Nov 2004
    Location
    tasmania
    Age
    60
    Posts
    387

    Default

    I have had success drilling holes in tiles with a standard masonary bit but do not have the drill on hammer . My main experience has been for tap fittings etc and then I drill a series of holes in a circle and chip them out . Easy
    Rick
    uhm , where am I ?

  4. #3
    Join Date
    Feb 2003
    Location
    Garvoc VIC AUSTRALIA
    Posts
    11,464

    Default

    I have done it like Rick.
    I have also used a grit edged hacksaw blade, Drill a hole through, thread the blade in and cut whatever shape you want.
    Regards, Bob Thomas

    www.wombatsawmill.com

  5. #4
    Join Date
    Nov 2004
    Location
    Melbourne
    Posts
    108

    Default

    I have found success in not going through the whole tile from one side, drill half way, then turn it over and come in from the other side...give it a try...may do the trick

  6. #5
    Join Date
    Jul 2003
    Location
    On the Downs, Darling SEQld
    Posts
    1,167

    Default Drilling

    You might try drilling from the unglazed side.................
    I was going to say "from the rear" but I know what you lot are like, lately,
    I thought better of it; for a while

    Also form a dam with Plasticine [or chewing Gum] and retain the water in the Damn.
    Somewhere back in the past dim years gone by, I recall using Kero.
    Yes! I know kero is good for some 'soft' metals also
    Navvi

  7. #6
    Join Date
    Jul 2004
    Location
    Sale
    Age
    68
    Posts
    1,328

    Default

    Try the above, just make sure you don't press down on the drill, just let its own weight do the job on a slow speed. A slight rock can help speed things up a bit, but if the tiles are porcelain you can toss this and all the above straight out the window. Ceramic suits the above for the very tough porcelain clays you need special diamond bits which you can sometimes pick up on ebay.


    John.

  8. #7
    Join Date
    Jun 2004
    Location
    Bunbury W.A.
    Age
    56
    Posts
    445

    Default

    Try sticking some reasonably heavy duty tape over the area that you wish to drill.
    Dont drill on hammer until you are thru the tile....if at all.
    if you always do as you have always done, you will always get what you have always got

  9. #8
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    63
    Posts
    13,354

    Default

    Copper tube.

    I use offcuts of various sizes from air-con installs, which I notch around one end with a hacksaw to create "teeth." These will usually fit straight iiton my drill-press chuck, but for larger diameters (like your 1") I make a simple jam-chuck. Ivan's already mentioned the next step: a circle of plasticine around the future hole and fill 'er with kero. To reduce breakout I'd drill from the front to the back using a rubber mat on the drill-press table. Drilled slowly, but with fairly firm pressure. Keep the kero level topped up... and remember not to smoke.

    The whole process can be sped up quite a bit by using a cutiing agent. Whatever's available'll do; valve lapping compound, lapidary cutting paste, even fine grain sand in some cases. In a pinch I won't turn my nose up at certain harsh, abrasive kitchen cleaners although I don't recommend any product containing bleach if you like your tools.
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  10. #9
    Join Date
    Apr 2005
    Location
    kyogle N.S.W
    Age
    50
    Posts
    4,844

    Default

    Ta Fella's. I'll give it a go.

  11. #10
    Join Date
    Sep 2004
    Location
    Melbourne, Victoria, Australia
    Posts
    123

    Default

    I have no problems using a tungsten carbide hole saw 32mm with a masonry drill bit in the middle, did 9 holes in wall tiles and one in porcelain floor tiles dry on the front lawn. Some of these holes were within 15mm of the edge of the tile and it went through without issue, not a single breakage. I drilled them all from the glazed side. The only stuff up I had was not taking off my titanium wedding ring, scratched a black mark into the glaze that was not removable. Luckily it was a tile not the basin or toilet pan.....

    Cheers
    Ben
    I reject your reality and substitute my own.

  12. #11
    Join Date
    Sep 2005
    Location
    campbelltown NSW
    Age
    67
    Posts
    623

    Default

    If all of the above fail, go to your local tile shop ( one of the larger ones ) and buy a tile hole cutter. I did this after a few different ways of trying and it was the best, I kick myself for not spending the few bucks (short at the time ), but what I wasted in tiles and time it would have been done quickly and properly.
    savage(Eric)
    savage(Eric)

    Never, under any circumstances, take a sleeping pill and a laxative on the same night.

  13. #12
    Join Date
    Jul 2003
    Location
    Gorokan Central Coast NSW
    Age
    79
    Posts
    2,765

    Default

    Quote Originally Posted by savage
    If all of the above fail, go to your local tile shop ( one of the larger ones ) and buy a tile hole cutter.
    Even better, mark where you want the holes and get them to drill them.

  14. #13
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    3,330

    Default

    If you can tolerate a fairly rough hole, for example if it is to be covered by a flange, then make 4 cuts in a square shape from the rear of the tile with an angle grinder. Knock out the piece where they intersect, and you will have a square 1" hole. The tile will be a bit weak around the hole but I've never seen that matter.

    Arron

  15. #14
    Join Date
    Aug 2004
    Location
    Melbourne
    Age
    52
    Posts
    149

    Default

    diamond hole saw, slow speed on the drill press , lots of water and patience.

    thats all you need and you will cut as many holes as you want...just remember lots of water and patience.

  16. #15
    Join Date
    Jun 2005
    Location
    Melbourne
    Age
    51
    Posts
    135

    Default

    I had a funny experience drilling holes into some porcelain tiles. After the initial two holes taking about 5 minutes each, and using a diamond tipped bit, I discovered a 'sweet spot'; a particular drill speed (on for 10 seconds, then 10 seconds in cold water to cool the bit). I also rinsed the hole frequently to get rid of the sediment. I was able to drill a hole ini 40 seconds, and got 7 or 8 holes out of one bit.

    Cheers, Justine

Page 1 of 2 12 LastLast

Similar Threads

  1. How to make my Dual Cyclone - Dust Extractor
    By Turbulance in forum DUST EXTRACTION
    Replies: 17
    Last Post: 22nd November 2008, 08:38 AM
  2. What is the best drill for women???
    By drillin away in forum HAND TOOLS - POWERED
    Replies: 64
    Last Post: 6th April 2008, 12:53 AM
  3. selling up tool sale
    By tasy_ted in forum METALWORK FORUM
    Replies: 1
    Last Post: 17th July 2005, 08:49 PM
  4. Cutting holes in tiles
    By JamesD in forum TILING
    Replies: 10
    Last Post: 11th May 2005, 02:25 AM
  5. how to drill perpendicular around circumference accurately?
    By TimberNut in forum WOODTURNING - GENERAL
    Replies: 13
    Last Post: 5th November 2004, 07:57 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •