Thanks: 0
Needs Pictures: 0
Results 16 to 30 of 34
-
2nd February 2019, 11:24 AM #16
It's looking good so far... should be a very nice piece if you can coax it through to a final form.
It certainly looks like it's good practice for all the 'kludges' one needs to know to keep a piece spinning safely!
- Andy Mc
-
2nd February 2019 11:24 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
3rd February 2019, 11:37 AM #17
Ah woodturning I used to do it onced.
Will keep an eye on this one.
-
3rd February 2019, 04:32 PM #18
Hardenfast.......on a different matter...how big is that shed of yours. Bloody hell, I 'd love to have that much room.
-
3rd February 2019, 08:05 PM #19
Thanks Skew. And yes, I think "coax" is probably the right word in getting this to a finish. Although, the improvement in stability is quite miraculous since the Aus Cedar rim had been affixed to the top. Putting a chisel on it now seems to be quite safe, even at a reasonably good speed. Good tip for the kludges, whatever they are. Going to try filling those termite holes with clear resin next.
G'day Phil. I'll keep the name change in mind. I'm determined not to spend too much time on this in total, although there will be a lot of brief sessions along the way. I started dribbling resin into the termite holes this afternoon. Just mixing up quite small batches and filling the holes until they stop running. Finding out that some don't. Perseverance.
Yes, there's some great stuff on the "Tube" now, Redbeard. Great for new ideas & techniques - whatever you want to do. I'm going to have a shot at a few "Bowls from a board" next. Have you seen those?Don't Just Do It.... Do It HardenFast!!
Regards - Wayne
-
4th February 2019, 08:49 AM #20Woodturner with a shed
- Join Date
- Nov 2007
- Location
- Caboolture, QLD, Aust
- Posts
- 236
I've seen a few variants on Bowls from a board, from just gluing a few pieces together to make a bigger blank to the full slice-n-dice of a segmented bowl. I've done a couple of the former but don't have the patience for the latter. I keep threatening to go out and hunt down a 10 by 4 stick of hardwood and chop it up for cheap blanks. Good bowl practice I would think.
You seem to have a bit of a knack for the segmented bowl game, that's the answer to those who call us "wood wasters".
Keep at it the ugly lump of pine. You might find something amazing inside.
Cheers
Redbeard
Cheers
Redbeard
-
12th February 2019, 09:18 PM #21
Yes, it's a nice big shed Skot - long time coming. It was supposed to be fully fitted out with 415V power and bathroom + amenity room by now, but I've had a little subdivision project which has been going sideways and taking up a lot of time and resources. In the interim I'm happy with what I've got, which is much better than some have to play in, I'm sure.
Don't Just Do It.... Do It HardenFast!!
Regards - Wayne
-
12th February 2019, 10:31 PM #22
So I got to spend a little time on this bowl project over the weekend. Again, I'm determined to keep my time to a minimum and spent around 45 minutes on Saturday and another 30 minutes on Sunday.
The segmented Australian Cedar rim I fitted to the top of it worked very well to stabilise the piece and I was able to start turning the outside into something like the desired shape. Earlier in the week I started to mix up small batches of clear resin and began dribbling it into the termite galleries. Haven't used resin in timber projects before so this was quite interesting. I had no way of knowing whether the termite tunnels went right through into the outside, so just kept filling them until most had stopped oozing - some didn't. Once the resin dried I turned the outside a little more and found that the sides of the bowl felt far more rigid.
However, the base was a maze of termite damage and I didn't think It was salvageable. I decided to fit a stabilising ring of Aus Cedar onto the base which would match the top. I cleaned up another piece of the dirty old stock I had (remarkable transformation) and then cut the segment pieces quickly on the drop saw, again using the thin slices of Kauri Pine as contrast. While this was drying I cut a flat base on the bottom of the pine and then sat it on the bench with some weight on the Cedar ring while the glue dried. This seemed to work just fine.
20190207_165903s.jpg 20190207_165934s.jpg 20190207_172816s.jpg 20190210_115425s.jpg 20190211_095159s.jpg
While waiting for the glue to dry I try to catch up on other projects in the shed, such as cleaning up and restoring some of my old machinery. For example, I have a few nice old Waldown industrial grinders on their original fluted pedestals which were originally 415V power. I fitted all new bearings and converted the heavy duty motors to 240V and am in the process of fitting variable speed controllers to them. I have just finished wiring the first one and tested it - it was a little tricky as I wanted to retain the emergency stop button in line with the speed controller. Beautiful old Australian made equipment that is irreplaceable now, and which runs without a hint of vibration. Once they are fully operational I will strip them back and give them a nice coat of Waldown hammered blue. Little side-track there.
20190210_115415s.jpg 20190211_101630s.jpg 20190211_172742s.jpg 20190211_174847s.jpg
Once the glue had dried on the segmented base I was able to put it back on the lathe with the chuck fixed onto my temporary particle board + formply backing plate - great improvement in appearance and stability. I then put a forstner bit in the drill chuck and centred a new chuck mortise on the base. I was then able to turn the bowl around and mount it from the base. I unscrewed the formply panel and then used the beautiful Vicmarc 18mm bowl gouge to turn off the pyneboard base I had glued to the segmented Aus Cedar rim, so I could have a look at the inside of the piece.
I think I've run out of image upload space with this post so I'll add a couple more in another short post.Don't Just Do It.... Do It HardenFast!!
Regards - Wayne
-
12th February 2019, 10:40 PM #23
Once the pyneboard was gone I was able to start cleaning up the inside of the bowl and thinning down the walls. The intention is to get it thin enough to see light coming right through clear resin in the termite holes. If you look closely at the centre image you can begin to see some light penetration already happening. I will need to fill in all the cracks with resin to keep it safe and continue to top up the tunnels. Little by little in between other chores.
20190211_175055s.jpg 20190211_184136s.jpg 20190211_184204s.jpgDon't Just Do It.... Do It HardenFast!!
Regards - Wayne
-
12th February 2019, 11:05 PM #24Woodturner with a shed
- Join Date
- Nov 2007
- Location
- Caboolture, QLD, Aust
- Posts
- 236
Hardenfast
Looking good, will make a lovely lamp.
Doesn't the resin make a wonderful mess when you start to turn it?
Patiently looking forward to the next instalment.
Cheers
Redbeard
Cheers
Redbeard
-
16th February 2019, 03:07 AM #25GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
Hard, Looks wonderful, nice save.
So much timber, so little time.
Paul
-
18th February 2019, 09:58 PM #26
OK - So finishing up on this one
I decided to finish this project a little short of my original scope to keep it within a reasonable time frame. I had originally intended to fill all of the termite holes and and cavities with clear resin, but I found it to be too time consuming. I managed to fill quite a few of them, and to ooze the resin into most of the cracks in the piece and this enabled me to turn the walls of the bowl down to around 10mm in thickness without any significant fear of calamity. I gave it a very rough sand and you can clearly see daylight through many of the termite galleries, as in the 4th image below.
20190216_123142s.jpg 20190216_123154s.jpg 20190216_123212s.jpg 20190216_132453s.jpg 20190216_141504s.jpg
Having achieved a reasonable shape and consistent thickness I spent another 5 minutes sanding it to an acceptable level for sealing. There are far too many termite holes and imperfections to try for a waxy finish, so I will give it a few coats of Wipe On Poly in gloss finish. A quick sand between coats and there it is.
20190216_144248s.jpg 20190218_191502s.jpg 20190218_191517s.jpg
I'm happy with the final result for this piece given the crazy condition of the starting components. It serves as a momento from our previous residence with all of the imperfections & irregularities that give it some character. The wife thinks it's brilliant, so that's a bonus. It has also served as a training exercise in dealing with unstable pieces, and for my first experience in turning with resin. I also hope it was of interest to some here.Don't Just Do It.... Do It HardenFast!!
Regards - Wayne
-
18th February 2019, 10:13 PM #27Woodturner with a shed
- Join Date
- Nov 2007
- Location
- Caboolture, QLD, Aust
- Posts
- 236
What do you say to a man with a large collection of meat cleavers on the back wall of his rather palatial shed but...
"Nicely done, Hard, nicely done".
Cheers
Redbeard
Cheers
Redbeard
-
18th February 2019, 10:24 PM #28
Thanks Redbeard. I'm glad to be finished with this one and hand it over to the wife.
You like the cleavers? I've collected them from all over the world and from many famous makers. I particularly like the American two-handed "hog splitters" which are around 34" (870mm) long overall. Most find it a somewhat macabre collection, but I view them all as beautifully made tradesman tools which have required great care in their usage and sharpening over the years. Just the same as my collections of chisels and hand planes etc.
MeatCleavers.jpgDon't Just Do It.... Do It HardenFast!!
Regards - Wayne
-
18th February 2019, 10:32 PM #29Woodturner with a shed
- Join Date
- Nov 2007
- Location
- Caboolture, QLD, Aust
- Posts
- 236
-
18th February 2019, 10:43 PM #30
I really like the bowl
Your perseverance certainly payed off in the end.
Cheers Matt,
Not sure what too say to a collection of meat cleavers, especially considering I’m sure I’m at least 33 percent meat still.
Similar Threads
-
Quartersawn piece for bowl too heavy
By Ben Lloyd in forum WOODTURNING - GENERALReplies: 7Last Post: 23rd October 2014, 01:18 PM -
Jacaranda Bowl 20 years in the making
By mañana in forum WOODTURNING - GENERALReplies: 3Last Post: 21st July 2014, 04:07 PM -
20 years and maybe 6 months old huon pine dining setting.
By artful bodger in forum WOODWORK PICSReplies: 3Last Post: 10th May 2014, 07:34 PM -
My Third Piece - A Segmented Bowl with WIP
By Hardenfast in forum WOODTURNING - GENERALReplies: 15Last Post: 23rd July 2007, 09:31 AM -
First Bowl in 20 years!
By Terry B in forum WOODTURNING - GENERALReplies: 14Last Post: 25th June 2006, 12:59 AM