Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
Thread: bush fix
-
12th September 2010, 06:08 PM #1GOLD MEMBER
- Join Date
- Sep 2008
- Location
- texas, queensland
- Posts
- 1,239
bush fix
going to make some hat stands and the centre colum of them will be around the 6 foot mark in length , i was just going to do them in 2 halves and join them with a tenon but then i decided to do a rough and ready lathe extend job .might need another brace under it yet though.
so here it is , dont know how it will go yet the piece of timber pictured is a 4x4 red cedar 6' foot 7and a half long .might have to knock up some kind of a steady yet not sure .
and yes i know the shed looks like a bomb site but thats about to change in the next week or so because i have to do a very big tidy up to make way for some canoe building .'If the enemy is in range, so are you.'
-
12th September 2010 06:08 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
12th September 2010, 07:10 PM #2Retired
- Join Date
- May 1999
- Location
- Tooradin,Victoria,Australia
- Age
- 73
- Posts
- 11,918
Gooday Texx.
You will need bracing.
The end needs bracing back to the bottom of the legs.
A brace from the top of the leg to half way down to the "end" brace.
A further diagonal brace from just near the switch to the base of the leg wouldn't hurt either with a brace to the centre of that to the top of the leg.
Racking forces are very strong in turning that length.
I would use 25x25x2 RHS.
See pic.
-
12th September 2010, 08:08 PM #3nine digits
- Join Date
- Jul 2010
- Location
- Geelong Vic
- Age
- 70
- Posts
- 616
At least now I know someone who's shed is as big a mess as mine
thanks
undies
-
12th September 2010, 08:40 PM #4GOLD MEMBER
- Join Date
- Sep 2008
- Location
- texas, queensland
- Posts
- 1,239
, i dont understand why i need more bracing in the old section of the lathe its pretty solid its 2x1 rhs (x 3mm i think )and the bed is 2x2 rhs ,but i do rekon i need to brace from the end of the extension back to the bottom of the legs , i was going to do it just never did it yet .
on the shed it is a biggish shed but not enough room to swing a cat at the moment , there are lister engines a half built trailer an almost finished chainsaw mill and a lot of stuff that does not need to be there so next week is big clean up and shift stuff out week , i might take a few before and after shots .
then i start building canoes in there need to make a 16 foot by 2.5 foot bench for that right up the middle of the shed .'If the enemy is in range, so are you.'
Similar Threads
-
My bush 'super'
By Greg Ward in forum TIMBERReplies: 9Last Post: 21st January 2010, 09:20 AM -
a bush fix
By pjt in forum SMALL TIMBER MILLINGReplies: 5Last Post: 1st November 2009, 11:41 PM -
Going Bush
By rod1949 in forum MOTOR HOMES, CARAVANS & CAMPINGReplies: 5Last Post: 2nd September 2009, 10:55 PM -
George Bush again
By munruben in forum WOODIES JOKESReplies: 2Last Post: 26th June 2007, 09:04 PM -
Pen from camellia bush
By Allan at Wallan in forum WOODTURNING - PEN TURNINGReplies: 3Last Post: 24th June 2007, 01:01 AM