Needs Pictures: 0
Results 1 to 11 of 11
Thread: Mandala Flower Of Life
-
17th June 2023, 05:13 AM #1
Mandala Flower Of Life
"CARVING FLOWER OF LIFE"
Hello once again everyone I've made some progress on this project. I have started carving through on the sides of the bowl. This has to be done almost all with knives and gouges, after I drill a hole in the widest place of the triangle. You will see the tools I'm using for this process in the photos, I've also rounded inside and most of the outsides flower peddles.Jack Of All Master Of None
-
17th June 2023 05:13 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
17th June 2023, 08:46 AM #2SENIOR MEMBER
- Join Date
- Feb 2018
- Location
- Shepparton
- Posts
- 508
very talented love your work
-
17th June 2023, 09:31 AM #3
WOW what talent you have!!!!
Just do it!
Kind regards Rod
-
18th June 2023, 01:46 AM #4
-
24th June 2023, 06:35 AM #5
"THE FLOWER OF LIFE"
I had some time this morning so I started the rim carving, I thought I would show where I was going with this project. Most of the carving was done with the knife in the photo. This Pommele Sapele carves much nicer than the Red Elm.Jack Of All Master Of None
-
30th June 2023, 08:39 AM #6
"THE FLOWER OF LIFE"
Hello everyone I have moved on with the carving on this project. I have carved a few flowers in various stages so you can get a better understanding of my process. You can see in the photos if you zoom in the first stage outlining cutting 1/16 "- 1/8" deep. This is very important to stop over cutting areas you do not wan cut. I have also shown the tools and files and sanding tools I use. I would have had even more carving done but I went back and have been refining the bowl section rounding, smoothing and sanding with220 grit.Jack Of All Master Of None
-
4th July 2023, 02:39 AM #7
THE FLOWER OF LIFE
Hello once again everyone I had some time to work and have made some good progress on this project. I'm over half way around carving flowers on the inside rim and have six of the flowers on the outside carved.Jack Of All Master Of None
-
20th July 2023, 12:22 PM #8
Mandala " FLOWER OF LIFE"
This semi segmented piece is made from Red Elm, Pommele Sapele and Tigers Eye stones. The finish size is 13" D x 6" with some pyrography work, the final finish is lacquer. After turning on the lathe the pattern was hand drawn and the pieces was hand carved.Jack Of All Master Of None
-
20th July 2023, 05:53 PM #9
Awesome job - looks spectacular !
-
22nd July 2023, 08:07 AM #10
-
22nd July 2023, 08:17 AM #11SENIOR MEMBER
- Join Date
- Feb 2018
- Location
- Shepparton
- Posts
- 508
What can I say but "WOW" you certainly are gifted and patient ,I like a lot.
Similar Threads
-
OUTSIDE AUSTRALIA Mandala Rose Engine O.T. and Accessories for Sale
By Bluemax in forum WOODWORK - Tools & MachineryReplies: 2Last Post: 27th June 2021, 09:12 PM -
Flower Pot Cyclone
By Barbarian_Child in forum DUST EXTRACTIONReplies: 6Last Post: 30th September 2011, 08:32 PM -
flower for..
By prometheus065 in forum MARQUETRY and INTARSIAReplies: 4Last Post: 14th March 2010, 10:14 AM -
a flower..
By kruger in forum WOODTURNING - PEN TURNINGReplies: 11Last Post: 27th November 2008, 10:35 AM -
Flower
By Beryl in forum WOODWORK PICSReplies: 8Last Post: 23rd March 2008, 03:00 PM