Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: A Vase That Holds Water
-
9th March 2016, 03:45 PM #1GOLD MEMBER
- Join Date
- Jun 2006
- Location
- Burwood NSW
- Age
- 82
- Posts
- 1,247
A Vase That Holds Water
G'day
I am sometimes asked by customers if they can put water in my vases and I have to explain that they are just for dried flowers .So I decided to make a couple that would hold water with the aid of inserts from Ikea .They are hollowed to about 180mm deep and the wood is camphor laurel .The finish is DO . Hollowing something with an entry this big is pretty easy also the pith was not included so there was little risk of splitting .
Comments welcome.
Ted
-
9th March 2016 03:45 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
9th March 2016, 06:27 PM #2
Good idea Ted, and well executed, . Couple of comments if I may. Have a look at Op shops for glass inserts, recycling is good. I would make the bottoms a bit bigger for stability. Similar shape to what you have but upside down. Don't think it is important for the wall thickness needs to be even, for this application.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
9th March 2016, 07:26 PM #3
Hi ted,
I like that idea, just go down to the pub for the inserts
My only comment would be maybe make them so you
can, t see the glass, a little bit higher,,, or you could
always use a middi glass
Well done !Cheers smiife
-
10th March 2016, 10:07 AM #4Senior Member
- Join Date
- Aug 2010
- Location
- Wattle Glen Vic
- Posts
- 116
-
10th March 2016, 02:09 PM #5
Ted great idea.
I do have a friend who uses casting resin or epoxy to seal the inside the type bought from Carbatec. its fluid enough to swirl around he then blows up a balloon one of those used by clowns to make strange shapes out of to force the mix into the sidewalls I haven't tried it myself.
-
10th March 2016, 04:40 PM #6GOLD MEMBER
- Join Date
- Jun 2006
- Location
- Burwood NSW
- Age
- 82
- Posts
- 1,247
Thanks for the comments.
After taking the photographs,I went to put the insert in the second one and discovered the base was slightly bigger so had to glue a tennon on the bottom and take a bit bit more out of the inside to make it fit . Bummer.
I'll see if I get a buyer at club sales this weekend .
Ted
-
10th March 2016, 05:40 PM #7
I have tried this with a test tube(plastic) but it did not work out too well. It needs to be wider at the top as what you have come up with. One of our club member used to coat his vases with something, it made the vase waterproof. I think it was a poly that he would pour in and swirl around then pour off the excess.
-
11th March 2016, 10:58 AM #8GOLD MEMBER
- Join Date
- Jun 2006
- Location
- Burwood NSW
- Age
- 82
- Posts
- 1,247
Ray
Many years ago I repaired a leaky fuel tank in my 4WD with a latex solution that I just sloshed round the inside of the tank . It worked , but on my first long trip I unexpectingly ran out of fuel . I later found that I had also sealed the passageway in the baffle plate so in effect was only using half the tank .Fortunatly I was able to get my hand in the sender unit hole and open the hole in the baffle plate .
I suppose I could have waterproofed these vases in a similar way but it wouldn't look real good and I'me sure it would cost more than the $2 or so for the glass inserts cost .
Ted
-
11th March 2016, 03:48 PM #9
-
11th March 2016, 04:32 PM #10
Bathrooms and shower areas wet areas.
In houses are now water proofed with what we call tanking.
It looks like latex paint tho I'm not sure
The big green places sell it
It's flexible and brush paintable wash up in water
Down side it's generally pretty ugly
Last time I used it was bright blue
Or bright green
Plus to be economically I buy it in a twenty litter drum I think for around the $100/150 dollar mark
So properly not much help
-
12th March 2016, 10:04 PM #11GOLD MEMBER
- Join Date
- Jan 2013
- Location
- the sawdust factory, FNQ
- Posts
- 1,051
West system epoxy... It holds water out of strip plank boat hulls and done well it'll give a reasonable finish.
mind, all boats leak, it's merely a question about how fast.
-
14th March 2016, 03:50 PM #12GOLD MEMBER
- Join Date
- Jun 2006
- Location
- Burwood NSW
- Age
- 82
- Posts
- 1,247
Thanks for the replies.
Someone liked it because it sold within the first hour of the sale.
Ted
-
14th March 2016, 05:30 PM #13
hey cool
now I've a use for all those schooner glasses I borrowed in my youthregards
Nick
veni, vidi, tornavi
Without wood it's just ...
Similar Threads
-
Advice for Cutting/Routing Hand Holds in Wooden Hamper
By meherenow7 in forum ROUTING FORUMReplies: 4Last Post: 17th September 2015, 12:48 PM -
What's the name of the handle that holds a tap?
By 19brendan81 in forum METALWORK FORUMReplies: 3Last Post: 27th November 2014, 01:42 PM