Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
15th March 2017, 06:21 PM #1SENIOR MEMBER
- Join Date
- Jun 2003
- Location
- Brisbane, Qld
- Posts
- 942
VL300 tailstock quill jammed - any ideas?
Hi folks,
Was drilling some pen blanks this afternoon - on my second blank I was winding the quill back in (so minimal force being applied), and it seemed to suddenly jam.
If I unwind the set screw on the handwheel I can spin the wheel just fine, but I can't get the quill to move at all. Anyone have any ideas?
Thanks,
Danny
-
15th March 2017 06:21 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
15th March 2017, 06:30 PM #2Senior Member
- Join Date
- Dec 2010
- Location
- Southern Highlands NSW
- Posts
- 444
Give Marco at Vicmarc a call. Good guy.
-
15th March 2017, 06:30 PM #3
If you've wound the quill right back into the tailstock casting they can bottom out and bind up easily. I'd give the handle a sharp tap with a rubber mallet (something I've done in the past when I wound the quill on my VL200 back too far). Hopefully we're talking about the same thing.
Cheers
Josh
-
15th March 2017, 06:45 PM #4SENIOR MEMBER
- Join Date
- Jun 2003
- Location
- Brisbane, Qld
- Posts
- 942
Thanks guys - I will give both of these a try!
-
15th March 2017, 07:07 PM #5SENIOR MEMBER
- Join Date
- Jun 2003
- Location
- Brisbane, Qld
- Posts
- 942
A sharp mallet tap didn't do the trick - and looking at it, the quill sn't retracted the whole way, still maybe 10mm out or so.
-
16th March 2017, 08:49 AM #6SENIOR MEMBER
- Join Date
- Jun 2003
- Location
- Brisbane, Qld
- Posts
- 942
Last night I took the quill out of the tailstock and gave it a bit of a clean. Will reassemble tonight (assuming I can get the quill back in the tailstock, it's a *very* tight fit!).
The Vicmarc instructions say to grease it before reassembly... I am the world's worst machinist, does anyone have any recommendations for what sort of grease?
-
16th March 2017, 05:41 PM #7SENIOR MEMBER
- Join Date
- Jun 2003
- Location
- Brisbane, Qld
- Posts
- 942
Think I have the issue pinned down with some help from Marco at vicmarc! The quill isn't rotating in the black bush which sits down near the back. Just waiting to see if Marco has a recommended fix.
I do love vicmarc - fast advice from someone who knows what they're talking about, and they even had a video on assembling a tailstock and quill assembly that was really useful!
-
18th March 2017, 02:47 PM #8SENIOR MEMBER
- Join Date
- Jun 2003
- Location
- Brisbane, Qld
- Posts
- 942
Freed this up by giving the bush a good hit of WD40 and then committing a bit of minor violence (steel rule stuck through the handwheel and given a few whacks with a rubber mallet). It's currently smoother than ever, hopefully it stays that way when the WD40 is gone!
Similar Threads
-
Extending tailstock quill travel
By Big Shed in forum METALWORK FORUMReplies: 6Last Post: 16th December 2009, 09:07 PM -
Tailstock Quill
By CameronPotter in forum WOODTURNING - GENERALReplies: 11Last Post: 27th February 2009, 02:45 PM -
Jammed chainsaw
By Cliff Rogers in forum SAFETYReplies: 6Last Post: 16th January 2008, 06:25 PM -
Jammed collet
By Ted in forum FESTOOL FORUMReplies: 17Last Post: 30th January 2007, 06:02 PM