Thanks Thanks:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Page 1 of 2 12 LastLast
Results 1 to 15 of 23
  1. #1
    Join Date
    Sep 2013
    Location
    Northern NSW on Qld border
    Age
    26
    Posts
    29

    Default Wood turning tools

    I have a set of HSS tools lent to me by my Grandad which is fine for turning spindle work but I am buying a new lathe in the next couple of days that has a scroll chuck and I would like to try and turn some bowls but I don't have a bowl gouge and my roughing gouge isn't adequete for roughing out big pieces of timber, so what is the best bowl gouge and roughing gouge suitable for turning 400mm diameter pieces that doesn't cost an arm and a leg?

    Cheers
    Bailey

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Age
    2010
    Posts
    Many





     
  3. #2
    Join Date
    May 1999
    Location
    Tooradin,Victoria,Australia
    Age
    73
    Posts
    11,918

    Default

    My choice for starters would be a 3/8 (1/2" shaft) Robert Sorby with a mild sweep back grind.

    Do not use a spindle roughing gouge on bowls. Why you don't use a Spindle Roughing Gouge on bowls.

  4. #3
    Join Date
    Sep 2013
    Location
    Northern NSW on Qld border
    Age
    26
    Posts
    29

    Default

    Don't worry I have seen the video before, when I first got my small lathe I tried to use one to hollow a bowl out but after that experience I didn't try again, but I do need a decent sized spindle roughing gouge for spindle work and roughing the outside of blanks also where is the best place to purchase the bowl gouge you mentioned?

  5. #4
    Join Date
    Jun 2004
    Location
    Mareeba Far Nth Qld
    Age
    83
    Posts
    3,069

    Default

    Quote Originally Posted by View Post
    My choice for starters would be a 3/8 (1/2" shaft) Robert Sorby with a mild sweep back grind.

    Do not use a spindle roughing gouge on bowls. Why you don't use a Spindle Roughing Gouge on bowls.
    Plus a 30mm wide and thick round nose scraper.
    Jim
    Sometimes in the daily challenges that life gives us, we miss what is really important...

  6. #5
    Join Date
    Feb 2012
    Location
    Nowra, NSW, Australia
    Age
    65
    Posts
    3,003

    Default

    Quote Originally Posted by Woodturner101 View Post
    ..... but I do need a decent sized spindle roughing gouge for spindle work and roughing the outside of blanks
    As I understood 's video, you shouldn't even use a spindle roughing gouge for roughing the outside of bowl blanks. Only for items with grain parallel to the bed.

    I'm a beginner, though, so perhaps or someone else could confirm this.

    I'm in the same position and am waiting until I get a decent bowl gouge later this week before trying any 'faceplate' turning. That video was enough for me.
    ... Steve

    -- Monkey see, monkey do --

  7. #6
    Join Date
    Jan 2004
    Location
    Towradgi
    Posts
    4,835

    Default

    Spindle Roughing Gouges are, for me, only used on spindles, ie between centres with grain parallel to the bed. As the name implies, it is to rough the blank from square (or roughly square) section to cylindrical. With practice, you can obtain a good finish, which makes the piece easier to work with.

    Personally I prefer P&N tools
    Pat
    Work is a necessary evil to be avoided. Mark Twain

  8. #7
    Join Date
    Oct 2007
    Location
    Horsham Victoria
    Posts
    901

    Default

    The Woodfast turning tools represent great value for money. I have trialled them and while there are better tools out there, which may hold an edge for a little bit longer, I think their tools are very accepatable. They have a good range and are well worth considering. Especially for roughing gouges when comparing prices. See link below.

    Woodfast Machinery Co. (Aust.) Pty. Ltd. -

  9. #8
    Join Date
    Sep 2008
    Location
    North Carolina, USA
    Posts
    2,327

    Default

    Woodturner 101,

    As advised above a 1/2 inch diameter (some call it a 3/8 inch) bowl gouge and a heavy scraper is all you need. Long and strong in both cases.

    The bowl gouge can be used as a roughing gouge for spindles.

    You will also need a grinder and jigs for grinding the bowl gouge. I prefer a slow speed, 1725 rpm here - 1400 rpm in AU, grinder, and 8 inch wheel. There is much discussion on this forum about sharpening. Do some research before you rush out and buy the "ultimate solution".

    I use: Wolverine Grinding Jig and: Wolverine Vari-Grind Attachment
    because they came with the used lathe I bought. There are others.

    There is also much discussion about brand of tool. A decent high speed steel bowl gouge, well sharpened, good technique, and 100 hours of practice will make nice bowls.

    I have Crown, Thompson, generic Sheffield, and Chinese high speed steel bowl gouges. The ability to stay sharp is about the same with all of them. The Chinese took more time to hone the inside smooth than the others. I do a little tuning on all my tools, bought or home made.

    I have a set of 8 Chinese turning tools I bought used for $20. The handles are small, the tools are rather short and the steel admits to "China", I assume carbon steel. I use the skew when I am working close to the chuck or drive center and often will do the whole spindle. As I sharpen frequently by giving it a few swipes on sandpaper on the bed of the lathe, it cuts as well as my Henry Taylor, which is also frequently sharpened the same way.

    Take any advice about the "only way" to do something with a grain of salt. There are many paths to the same place.

    Look up Robo Hippy's utube videos on making bowls with scrapers.

    You would save time and frustration if you were to get some instruction on turning and sharpening. Each hour of instruction will save you about 10 hours of trial and error.

    If you join a men's shed you will be exposed to different lathes, tools, and techniques. Adopt what works for you.

    Welcome to the addiction.
    So much timber, so little time.

    Paul

  10. #9
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    63
    Posts
    13,354

    Default

    Quote Originally Posted by View Post
    My choice for starters would be a 3/8 (1/2" shaft) Robert Sorby with a mild sweep back grind.
    Ayup. A 1/2" bowl gouge is a great starter. (For what it's worth, the 3/8" measurement is the width of the flute and comes about 'cos some mfrs sort their wares by flute size, others by OD. Just to make life "simple" for us. )

    But, , I'm sorta stumped as to why you suggest Robert Sorby? I'm definitely not a fan of 'newer' RS tools. (The old RS carbon steel, now that's a different matter! )

    Unhandled P&N's are cheaper - well... the last time I looked, anyway - and IMHO better steel. Admittedly the quality control seems to be a bit slipshod and the flute surfaces often need a good dressing before their first use. But that's a one-off process and the reslt often gives the equivalent of a tool worth twice as much.

    (I'm thinking "cheap first gouge" here. What's a li'l elbow-grease when $$$ are tight, right? )

    Maybe suggested Sorby because of the flute profile/cross-section? It seems that every Mfr. has their own ideas of how deep/wide/profiled the curve of the flute may be in relation to the bar stock and this can make a HUGE difference in both usage & ease of sharpening. Esp. for a first-timer.
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  11. #10
    Join Date
    Sep 2008
    Location
    North Carolina, USA
    Posts
    2,327

    Default

    Skew,

    I had some Christmas "crazy money" some years ago and went to buy my first bowl gouge. I went to a place that had Crown & Robert Sorby. I went with the Crown because it was less expensive and looked about equal.

    Still are: Crown 3/8" Bowl Gouge 241 | Klingspor's Woodworking Shop

    *Sorby Bowl Gouge 3/8" (842LH) | Klingspor's Woodworking Shop
    So much timber, so little time.

    Paul

  12. #11
    Join Date
    May 1999
    Location
    Tooradin,Victoria,Australia
    Age
    73
    Posts
    11,918

    Default

    Quote Originally Posted by Skew ChiDAMN!! View Post
    Ayup. A 1/2" bowl gouge is a great starter. (For what it's worth, the 3/8" measurement is the width of the flute and comes about 'cos some mfrs sort their wares by flute size, others by OD. Just to make life "simple" for us. )

    But, , I'm sorta stumped as to why you suggest Robert Sorby? I'm definitely not a fan of 'newer' RS tools. (The old RS carbon steel, now that's a different matter! )

    Unhandled P&N's are cheaper - well... the last time I looked, anyway - and IMHO better steel. Admittedly the quality control seems to be a bit slipshod and the flute surfaces often need a good dressing before their first use. But that's a one-off process and the reslt often gives the equivalent of a tool worth twice as much.

    (I'm thinking "cheap first gouge" here. What's a li'l elbow-grease when $$$ are tight, right? )

    Maybe suggested Sorby because of the flute profile/cross-section? It seems that every Mfr. has their own ideas of how deep/wide/profiled the curve of the flute may be in relation to the bar stock and this can make a HUGE difference in both usage & ease of sharpening. Esp. for a first-timer.
    My first choice is Henry Taylor but they are expensive and hard to find out here.

    Yes Skew, you are right, it is the flute shape. The parabolic shape is easier to sharpen, clears shavings well and can be used on spindles. The P&N 3/8 (1/2") is a pig to sharpen easily and in my opinion too narrow in the flute but in certain circumstance is very useful because of its strength when overhanging the rest.

    Woodturner 101 asked for a good all round, general purpose bowl gouge and IMO the Sorby fits the bill, there are cheap Chinese variations but I don't bother with them generally.

    A good scraper as others have suggested is also a must.

    Woodturner 101, I am coming to Sydney in the next couple of weeks. If you want some help, I would only be too happy to come around.

  13. #12
    Join Date
    Sep 2013
    Location
    Northern NSW on Qld border
    Age
    26
    Posts
    29

    Default

    Thanks for the help and others, I will probably go with a Robert Sorby Bowl gouge or P & N and once my Bank account recovers from my recent wood turning purchases I will get a decent size scraper, Also do I actually need a sharpening jig? because I have just been sharpening my gouges,scrapers and skews freehand on the grinder.

  14. #13
    Join Date
    Sep 2008
    Location
    North Carolina, USA
    Posts
    2,327

    Default

    Quote Originally Posted by Woodturner101 View Post
    Thanks for the help and others, I will probably go with a Robert Sorby Bowl gouge or P & N and once my Bank account recovers from my recent wood turning purchases I will get a decent size scraper, Also do I actually need a sharpening jig? because I have just been sharpening my gouges,scrapers and skews freehand on the grinder.
    My first turning tools were a bench chisel and screwdriver sharpened on a belt sander.

    I sharpen the home made Bedan type tools and scrapers using the platform, and rest the skew on the edge of the platform.

    I like the repeatability of using the varigrind jig and I can get the bowl gouge sharp with just a bit of metal taken off.

    I have a 5/8 bowl gouge with a long fat handle that is about 3 feet long and awkward to swing using the varigrind. I do that free hand using the edge of the platform. I do not get as nice a swept back profile with that.

    You might try sharpening free hand and see how you do. There are plans and instructions on making grinding jigs. Do a search on the internet.

    I highly recommend for instruction. He has many years of experience as a professional turner. Many on this forum have praised his teaching ability.

    In the photo below the tool at the top is my favorite scraper. It is a 2 X 12 X 3/8 inch thick high speed steel planer blade. I got four for $15 at an auction. The others are screwdrivers ground for making a recess or spigot to grab with a chuck, the home made Bedan type tools, and a scraper made from a lawn mower blade. It is used for roughing bowls made from dirty roots and stumps with imbedded dirt, stones, nails, and wire.
    Attached Images Attached Images
    So much timber, so little time.

    Paul

  15. #14
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    63
    Posts
    13,354

    Default

    Scrapers, skews and the like are the simplest to sharpen and - unless you're making an unusual profile - are generally easily sharpened freehand.

    Gouges, both spindle & bowl, take a bit more practice & control, but are also easily done freehand when the profile is more or less "straight across."

    Where a good sharpening jig becomes an advantage is when the profile becomes more complicated: such as the swept-back wings on bowl gouges. This is where most people run into difficulties... but with a properly set up jig, these grinds are a breeze to make, are replicable and waste a minimum of tool steel.


    As you may realise, I sharpen all my tools freehand except for these complex grinds; for those I use the Teknatool "Fingernail" jig. (Actually, I use their old orig. jig, sold before they "specialised it" to become part of their sharpening station suite. )

    The few gouges I use on it have the correct settings (for the jig) punched into the handle, so when they go to the grinder it's just a few seconds to reset the jig appropriately for that tool and make a quick pass or two.


    Do you need a sharpening jig? No. Should one be on your wish list? IMHO, yes. Once you move into the fancier grinds, most definitely!
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  16. #15
    Join Date
    Apr 2007
    Location
    Adelaide Hills, South Australia
    Posts
    4,311

    Default

    Quote Originally Posted by Woodturner101 View Post
    Also do I actually need a sharpening jig?

    For bowl gouges:

    If you are a Richard Raffan, I'd say definitely no.

    If you are Brendan Stemp, who turns on most days, likewise, no.

    If you are Robo Hippy, who has told us he mostly uses scrapers anyway, no.

    But, if you are like most of us, I would suggest you do so, at least to begin with.

    DO get a very experienced bowl turner to configure the jig for your gouge.

    Jig settings are specific to the flute profile to create the desired grind.

    I like Doug Thompson's maxim on matched flute:grind profiles.

    Sharpen your gouge with a jig for your first 1,000 bowls.

    After that, you will know if freehand is for you.


    If the cost of a jig is an issue, you can make your own.

    This simple bowl gouge sharpening jig would do the job for me.

    And, if you are into metal work, this one is a bit more like the commercial ones.
    Stay sharp and stay safe!

    Neil



Page 1 of 2 12 LastLast

Similar Threads

  1. Carbide Wood Turning Tools
    By carbidetools in forum WOODTURNING - GENERAL
    Replies: 16
    Last Post: 5th March 2010, 10:35 AM
  2. Wood Turning Tools
    By colbra in forum WOODTURNING - GENERAL
    Replies: 9
    Last Post: 11th July 2004, 11:57 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •