Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 19
-
13th April 2011, 01:18 PM #1
Woodfast mini or jet midi lathe??
I am thinking of buying a midi lathe ( already have bigger lathe)
Can anyone help with info ? The Vicmarc is too $ to justify, so at this stage its down to two ( although tell me if I am missing something)
The Woodfast m305 and the Jet midi 1220 (the mini model is too small for what I want)
I have 30mm gear so the Woodfast gets one vote ( I don't think the Jet has 30mm spindle ?)
I realize there is a difference in motor power ( I am looking at non variable speed- I know V speed is good)
Do they have similar size drive belts/ head stock bearings etc. eg: are they similar? or do you spend the extra for the jet?
any help, much appreciated.
-
13th April 2011 01:18 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
13th April 2011, 01:53 PM #2
Woodfast wins hands down in the comparo
Vicmarc is really way above all these in quality and worth the extra $$$$$$Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
13th April 2011, 03:40 PM #3
thanks Jim, have you any experience with the Jet? re belt sizes bearings etc.
Sure Vicmarc are great, but the Woodfast are sooo cheap. Hard to go past if you are only using it ever so often.
-
13th April 2011, 05:20 PM #4Retro Phrenologist
- Join Date
- Oct 2009
- Location
- Springfield NSW
- Age
- 70
- Posts
- 1,007
I have had my Woodfast for just over 12 months now (secondhand when I got it), and I just love it. I can't give you a comparison, but I don't think you would be disappointed with it.
-
13th April 2011, 05:57 PM #5
thanks Avery, does it have much 'power' eg: does the belt slip etc or anything like that if you turn something near its capacity. eg: 300mm in diam.
I know they are only a 'smallish' lathe but not much point having a big swing if the belt slips etc.
-
13th April 2011, 06:23 PM #6
The woodfast has very good power for its size.
You have to remember with any of these smaller lathes that you take smaller cuts.
The belts have good drive but when set up properly will slip slightly to give you an escape route.
You never overtighten poly v belts.
If you need more power then get a lot larger lathe These are not called midi lathes for nothing or if you want power in the midi lathe then you need the Vicmarc VL150
Respect the machineryJim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
13th April 2011, 07:50 PM #7Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Inventor, I was talking to Gary Pye's young fellow alst week. Gary is adding a midi to his own brand of lathes. As you are in Nth. NSW it might be worth a phone call or e-mail to him.
Otherwise, Jim is spot on!
-
13th April 2011, 08:30 PM #8
I had a jet mini lathe and replaced with a Woodfast midi. The Jet was a bit small and I found I didn't need the variable speed on a small lathe. The Woodfast midi I bought without the variable speed option. I thought the price of the variable model a bit high. Speed changing on the Woodfast is quite easy and quick.
I will admit that variable speed is very handy on a "full" size machine.
Both machines could do with a bit more power, but as has been said before, you have a pony not a draught horse.
I am very happy with the Woodfast machine.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
13th April 2011, 09:32 PM #9
The Lathes.
Hi INVENTOR,
What Jim & Powderpost say are correct as far as I can see. Know of 2 Chaps this end with W/Fast, & they could not be happier.
The Black Plastic Cover over the Belt Compartment is Brilliant, as it just slips away from you & there is the Belt. If it breaks the new belt is a breeze to put on, where as my Leda Craft belt change would take 1/2hr.
The only other thing is that there are 2 Woodfasts. 1 you buy comes from W/F in Adelaide, & it is the dinkydi Lathe, that says "Woodfast Australia".
The other 1, is most likely the most common, & nothing wrong with it at all, BUT don't ring the People in Adelaide to fix it, if something goes wrong, because they will not.Regards,
issatree.
Have Lathe, Wood Travel.
-
13th April 2011, 09:46 PM #10Retro Phrenologist
- Join Date
- Oct 2009
- Location
- Springfield NSW
- Age
- 70
- Posts
- 1,007
I have turned a few platters at near maximum size with no problems. You have to be a bit more delicate with your cuts than you would with a full sized lathe, but that is just the way it goes. If you really get into it with a big bowl blank and a big gouge, the motor will struggle and the belt might slip, but that will be the way it is for any small lathe. The only other lathe that I use fairly often is an old but well maintained Hafco WL18, the little yellow Woodfast is better in every way. If we were comparing cars, I guess you would call it power to weight ratio.
-
13th April 2011, 09:46 PM #11
Thanks for the replies thus far. I know that they are not large lathes and when turning you would need to keep that in mind. but with a modest size belt/pulleys and motor they potentially could do reasonable work, given the 300 swing
I think I can easily justify the non variable speed version, particularly given the belt/pulley is so accessible and there is a big jump in price.
I have seen the Jet Midi at Gary Pye ( he has sold them for some time but if they are still not 30mm spindle ( not sure) then it does make it more difficult for me ( changing chuck adapters etc)
-
13th April 2011, 10:28 PM #12
Inventor, the Jet 1220 lathe is a 1" x 10 TPI spindle thread.
Dallas
-
14th April 2011, 12:17 AM #13
I have turned a Jarrah bowl 280mm x 180mm on my Woodfast M305 with NO slipage of the belt . The Lathe is now 2 years old have not replace any part.
I bought it from woodfast in Adelaide cost me $30 more then other places was asking for it at the time. Was evey happy with the service I got from Woodfast. AND if it breaks down Woodfast will assist me in repairs and parts which the othe place could not.
I have no intests in Woodfast in any way but as a very happy customer
Trevor
-
14th April 2011, 12:42 AM #14.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
I have had the woodfast for just over 3 years.
My tailstock camlock snapped about the third time I used it. I didn't bother getting a replacement but instead made a newer, thicker one.
The headstock indexing gear grub screw kept self loosening and rattling around and being loathe to use locktite on it I added another - seems to be OK
Other than that I have worked it hard and for such a small lathe it seems to have coped reasonably well.
-
14th April 2011, 07:41 PM #15
thanks guys for your responses, sounds like some 'happy Woodfast customers'.
Similar Threads
-
Woodfast M305 Midi Lathe
By watsrags in forum WOODTURNING - GENERALReplies: 16Last Post: 13th February 2016, 01:55 PM -
Chuck for Woodfast mini lathe
By haggismuncher in forum WOODTURNING - GENERALReplies: 13Last Post: 21st June 2010, 07:32 PM -
bowl saver on woodfast midi lathe
By Dave.w in forum WOODTURNING - GENERALReplies: 12Last Post: 27th April 2010, 08:13 PM -
Full size or mini/midi lathe for pen turning???
By Wooden Ewe? in forum WOODTURNING - PEN TURNINGReplies: 6Last Post: 15th September 2008, 01:43 PM -
Woodfast Midi Lathe (M305)
By DuncanH in forum WOODTURNING - GENERALReplies: 34Last Post: 21st July 2008, 08:48 AM