Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 27 of 27
-
26th August 2010, 03:50 PM #16
Jim just saw this on Nova's site.
Comprehensive Instructions <o> </o>
All <st1:stockticker>NOVA</st1:stockticker> products come with comprehensive support and instructions to enable to you get the most out of your investment.
-
26th August 2010 03:50 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
26th August 2010, 04:02 PM #17
Ian have a look at this a its whats called a Legacy Lathe but with indexing on a normal lathe there are ways to do much the same things.
-
26th August 2010, 05:23 PM #18Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
26th August 2010, 05:34 PM #19Deceased
- Join Date
- Jun 2003
- Location
- ...
- Posts
- 7,955
I made one myself, not too hard to do.
Peter.
-
26th August 2010, 06:31 PM #20
I'll go one better, my indexing is built in to the headstock spindle
-
26th August 2010, 06:53 PM #21
I like my Nova 3000 for it Fred haven't used it but will be soon.
Jim I am sure I said similar in another thread when rssr mentioned indexing on his chuck I asked to see to see his set up didn't have one i think.
Sturdee yes simple to make a index pin set up, still yet to do one for the Jet Mini I have the plate and the tongue just need to mount it.
-
26th August 2010, 07:48 PM #22
Y'know, the forum still has a Search feature. Here's a simple, but effective, device for engaging the rim holes: https://www.woodworkforums.com/f8/index-jig-mc900-87645/
And speaking of cupcakes, I just eyeballed the index positions for scratching the flutes for a new batch of cupcake earrings. ( https://www.woodworkforums.com/f8/cup...rrings-113147/ ). Test marketing this coming Saturday.
Cheers,
JoeOf course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
26th August 2010, 08:19 PM #23
-
1st September 2010, 04:01 PM #24
Hi Nai and others
attached is a pic of the indexing jig I made for my MC900 - it clamped down to the bed and had a pointed screw that wound up into the indexing holes around the outside of the Vicmark chuck.
it was made out of plywood - easy and effective, but a bit fiddly.
cheers,
Colin
-
1st September 2010, 09:21 PM #25
-
1st September 2010, 11:21 PM #26
Hi Ian
The jig is really only about being able to hold the chuck still in a known position while you do whatever to the workpiece.
The Vicmark chuck has 24 numbered indexing holes equally spaced around the outside edge, and another 24 on the back face. That means each hole is 15 degrees away from each of its neighbours, so as you rotate the chuck (and the workpiece) hole by hole you are stepping around the piece in 15 degree increments.
My jig clamped onto the bed right under the chuck, and I screwed the pointer up into one of the perimeter holes (say no. 1) and locked it with the wingnut. Then you do whatever you want to do to your workpiece at that point - maybe rout a flute along the outside, or drill a hole, or carve a feature, or just make a pencil mark along the top of the tool rest to locate something. Then undo the pointer screw, turn the chuck the number of holes (ie the number of 15 degree steps) you need to suit your pattern, lock it up and make your next feature. Keep going until finished.
Other systems use a springy or spring-loaded bar attached to the headstock to engage the holes and hold the chuck in place - the result is the same. The beauty of my jig was that I made it from scraps, plus a couple of hardware bolts and T nuts and it didn't involve drilling holes in the lathe. However it was bit slower to use than a springy bar would be.
One of the things I made with it was a raised cake stand in Jacaranda, with 8 (I think) pieces of 25mm diameter cedar set into it (at 45 degree spacings). From memory I think I used the jig to accurately mark out the hole centres which I then drilled with a 25mm forstner bit on the drill press.
One of the challenges is to make sure you keep count of how many holes you turn the piece each time - one step of one hole too many will mean you finish up one hole past where you started - tends to mess up the pattern.
This post ended up longer than I thought - sorry if I have been a bit long-winded, but I hope it helps.
cheers,
Colin
PS - I gave the jig to Ozkaban (Dave) when I moved from the MC900 to a Nova 3000 - he now has a Vicmark lathe so he might be pursuaded to pass it on if he still has it.
-
2nd September 2010, 12:09 AM #27
Hey Colin
Thanks heaps that makes me un derstand it a bit better and will do well in the future when i use it and its ok to be detailed sometime thats what people need i think i might make one and play around a little bit
Cheers Nai
Similar Threads
-
Which chuck for the Vicmarc VL100?
By aak in forum WOODTURNING - GENERALReplies: 41Last Post: 17th March 2009, 02:40 PM -
Vicmarc 120 Chuck
By Auzzie turner in forum WOODTURNING - GENERALReplies: 12Last Post: 20th May 2006, 05:49 PM -
Vicmarc chuck
By azturner in forum WOODTURNING - GENERALReplies: 1Last Post: 4th September 2003, 03:51 PM