Needs Pictures: 0
Results 1 to 7 of 7
Thread: Hexagonal box lids/bases
-
15th April 2019, 04:15 PM #1
Hexagonal box lids/bases
Hi everyone,
I'm setting about making a series of hexagonal boxes (we've just gotten into beekeeping!) and while the cases are no problem at all, I'm having trouble getting accurate, repeatable lids. I've tried the mitre saw and table saw but both seem to produce lids that are just a bit off (say 1-2mm long or short on a couple of sides).
If anyone has any experience in producing these kinds of shapes I'd be grateful for advice. I need to be able to measure the inside lengths of the assembled case sides and then cut a lid/base exactly to fit.
thanks heaps
Warwick
-
15th April 2019 04:15 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
18th April 2019, 06:27 AM #2GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Sydney
- Posts
- 1,557
were you trying to rebate the box frame for the lid to sit into?
The only thing I can suggest is to cut a circle, preferably using a bandsaw circle cutting jig, and with each segment measure the distance and cu by hand using Japanese flush saw, greater accuracy, and can and sand the final fit
-
18th April 2019, 08:53 AM #3
I make the lid and bottom panels as follows:
1. Draw a circle of the appropriate diameter using a compass
2. Draw a diameter through the centre of the circle
3. With the compass centred on each intersection of the diameter and circle, draw arcs intersecting the circle.
4. Draw lines between adjacent points on the circumference - the ends of the diameter and the arcs. This is the most accurate method of constructing a hexagon, as it avoids the accumulation of errors you get if you just step off the radius around the circumference.
5. Cut the hexagon slightly oversize using a hand saw or bandsaw.
6. plane down to the construction lines.
Hex box - Camphor laurel, Jarrah & Tas myrtle small .jpg
-
18th April 2019, 09:37 PM #4GOLD MEMBER
- Join Date
- Apr 2014
- Location
- Kew, Vic
- Posts
- 1,069
Lovely box, that, Alex. Care to give us any pointers?
Brian
-
19th April 2019, 10:02 AM #5
Thanks Homey, glad you like it.
I guess the main things are the normal pointers - measure accurately, cut the angles accurately etc. As always, when glued up, ensure the diagonals are all equal.
With this type of lift-iff lid, I cut the slots for the lid and bottom panels, and a slot where you'll separate the lid, on the table saw before cutting the sides to length. The side material should be long enough that you have some spare to use when setting the saw to cut another slot on the other side to finally separate the lid, after the box is glued up. The inside & outside slots are set so their corners line up and the he lid is a neat fit.
Hope this is clear, let's know if you have any questions.
-
20th April 2019, 09:28 AM #6GOLD MEMBER
- Join Date
- Apr 2014
- Location
- Kew, Vic
- Posts
- 1,069
Thanks for that, Alex. My apologies - a vaguely-worded question by me. I should have asked how the top was created. The pattern looks to be part of the lid rather than an insert. A scroll-sawn lid over an insert panel, perhaps?
I was prompted to re-read your detailed contributions to Box Bits on this forum and would highly recommend them to any new box makers. Some great tips and techniques there.
Regards,
Brian
-
20th April 2019, 09:35 AM #7
Yes, it's a scroll-sawn insert glued to the lid panel. The most difficult part was shaping the insert after sawing, without breaking it. Also, I had to put wax resist on the panel and the insert, so that any glue squeeze-out could be removed. Very time-consuming work with a cotton bud.
Thanks for your comments about my Box Bits pieces - glad they're helpful.
Similar Threads
-
hexagonal
By pugwash in forum WOODWORK - GENERALReplies: 23Last Post: 9th March 2013, 02:49 PM -
Hexagonal Box
By homesy135 in forum BOX MAKINGReplies: 0Last Post: 16th May 2011, 05:34 PM -
Hexagonal Box
By Ruddy in forum BOX MAKINGReplies: 13Last Post: 10th June 2010, 12:03 AM -
Hexagonal Dovetailed Box
By GDL in forum BOX MAKINGReplies: 15Last Post: 15th October 2007, 08:43 PM -
Hexagonal Box
By watson in forum BOX MAKINGReplies: 15Last Post: 2nd April 2007, 08:28 PM