Results 16 to 30 of 47
-
2nd August 2017, 08:42 PM #16
-
2nd August 2017 08:42 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
2nd August 2017, 10:47 PM #17
thanks
regards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
3rd August 2017, 12:36 PM #18GOLD MEMBER
- Join Date
- Feb 2005
- Location
- Sydney
- Age
- 74
- Posts
- 1,389
I've got plenty of white beech, from 300mm wide inch boards x 3 metres long to 270x270 thick posts for carving
Greg
-
3rd August 2017, 03:41 PM #19
Thanks for posting this build Alex. That will be an exceptional box.
What have you used to make the escutcheon plate?And my head I'd be a scratchin'
While my thoughts were busy hatchin'
If I only had a brain.
-
3rd August 2017, 05:57 PM #20
-
4th August 2017, 01:34 PM #21
I glued the leg structures on, and also the scutch plate and lifter. The lifter is dowelled using Japanese wooden nails. I did a bit of experimenting with them - my initial idea was to leave a little bit protruding and shape it like a shallow pyramid - but decided to pare them flush with the lifter.
Once they'd dried and been cleaned up, I fitted the latches and hinges. Perhaps it's a relic of my days using butt hinges, but I still fit them one screw at a time, in case any fine adjustment is needed. With Andrew Crawford's SmartHinges, this is rarely needed. For the initial hinge fit, I use steel screws, because the last thing I want is to break a screw off, and this is more likely to happen with brass. The steel screws are as scarce as rocking horse manure, and these were kindly sent to me by Dengue - I don't know where he found them, but thanks, Dengue.
IMG_1208.jpg
IMG_1211.jpg
IMG_1209.jpg
IMG_1207.jpg
IMG_1206.jpg
The next steps will be to remove the hinges & lock, oil the box, and make the tray and its supports to fit.
-
5th August 2017, 12:15 AM #22
Hi Alex
what size steel screw do you need?
I might have some suitable ones back in Canada.regards from Alberta, Canada
ian
-
5th August 2017, 09:47 AM #23
Interesting box - I'm not sure I like the form work but it is sort of growing on me
more importantly than what I think - I hope the client likes it.
I also might have the odd steel screw lying around - let me know the size
We also often get such dumped at the men's shed and the chaps down there don't really use themregards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
5th August 2017, 04:13 PM #24
Alex,
Love the combination of timbers. A question; you've said previously that the bottom panel is entirely floating (presumably housed in a groove in the sides), but is the top panel also completely glue-free and floating in a groove as well? Or do you tack it in place with a small amount of glue somewhere near the centreline of the end grain edge?
Also, any trick for getting such a neat job with the hinge cutouts? I'm guessing set up on a router table with a stop block at the appropriate point on the fence, and take multiple shallow passes with a spiral downcut bit?
I personally like the design of the leg structures. You always seem to come up with interesting ideas for this !
Cheers
-
5th August 2017, 04:16 PM #25
Re. screws for the hinges, I keep a few gauges/lengths of tine brass square drive screws (Sachys) for this, and always make sure i buy some of the exact same size in steel for the initial installation. One brass screw snapping off in a hard timber is enough to spoil your whole week !!
Bit of a knack to clocking the screws so that the square drive holes all line up though.....
-
5th August 2017, 04:57 PM #26is the top panel also completely glue-free and floating in a groove as well? Or do you tack it in place with a small amount of glue somewhere near the centreline of the end grain edge?
The screw size is #3 5/8". I don't need more at present, thanks, as I re-use the ones have.
Also, any trick for getting such a neat job with the hinge cutouts?
-
6th August 2017, 11:25 AM #27
Cheers Alex - as always, lots of useful information in your box-making posts
-
7th August 2017, 10:25 AM #28
-
8th August 2017, 08:24 PM #29
Now that the carcass is finished, I've started on the liners and tray. The liners are a tight fit, but are not glued in. they are there to support the tray.
The tray will be white beech, with a suede lined bottom the same as the carcass.
[ATTACH=CONFIG]417878[/ATTACH
I've given the liners a coat of oil, as well as oiling the inside of the tray sides before gluing it up. While waiting for the tray to dry, I removed the brassware and gave the carcass its first exterior coat of oil.
]IMG_1227.jpg
-
8th August 2017, 10:32 PM #30
I walked into the Bungendore Woodworks yesterday and from across the room spied two boxes -- my immediate reaction was "they're Alex's boxes"
I could tell by the feet.
Always impressed by your work.regards from Alberta, Canada
ian
Similar Threads
-
Tiger Myrtle.
By TasSculptor in forum TIMBERReplies: 3Last Post: 15th October 2015, 07:03 PM -
Tiger Myrtle
By TasSculptor in forum SMALL TIMBER MILLINGReplies: 17Last Post: 24th June 2015, 07:54 PM