Needs Pictures: 0
Results 16 to 30 of 32
Thread: Wave Box
-
14th July 2017, 04:04 PM #16Member
- Join Date
- Apr 2015
- Location
- Blenheim, New Zealand
- Age
- 78
- Posts
- 55
Hi Ruddy,
Here is the first trial using veneers from my bandsaw (about 1 mm thick), cut the same way you outlined, in a stack, but using a knife instead of a scroll saw. Woods are Totara and Kahikatea. The pieces were applied to an MDF backing with Titebond 1 using the dry coat/hot iron method, which I'd not used before. That seems to work well.
This came out better than I expected although there are a few gaps and missing tiny points here and there. Okay for a first test piece but not good enough to use on a box. I thought applying a finish would make the defects jump out so I just waxed it and much to my surprise they actually seemed to disappear. Cutting this with a knife is not easy but I expect I'll persist with this as I can't imagine that cutting it with a fretsaw would be easy either. I do hanker for a Knew Concepts saw now though.
Rex
IMG_3590.jpg IMG_3589.jpg
-
14th July 2017 04:04 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
14th July 2017, 04:11 PM #17
Id imagine if you hot sand shaded the parts it would exaggerate the 3D-ness
-
14th July 2017, 05:07 PM #18
Hi Rex,
Those lid inserts look really good especially as you have hand cut the pieces with a knife. My first effort making this item was done using some thin veneers of contrasting colours. I was quite happy with the result
but thought it would be easier using thicker veneer. The thicker assembly gives you the opportunity to parallel sand through a drum sander. The Knew Concepts fret saw looks like an ideal low cost alternative to a scroll saw.
I shaded my lid with a couple of different brown colouring pencils before applying the finishing coats.
Hot sand shading looks good but it is a skill I have never tried. Using a pyrography pen using a flat bladed nib at low temperature also works well.And my head I'd be a scratchin'
While my thoughts were busy hatchin'
If I only had a brain.
-
27th July 2017, 09:19 PM #19
Very effective lid Ruddy - it really does look like the lines taper across the length of the wave as double.d said.
Getting an idea for an end-grain cutting board here - might even happen one day once I get an inverse set of cutters to match my curved shaper blades
-
27th July 2017, 10:35 PM #20
Hi Vern,
The end grain cutting board is already on the To Do list but at the moment it is probably number 65 on the list!And my head I'd be a scratchin'
While my thoughts were busy hatchin'
If I only had a brain.
-
30th July 2017, 03:01 PM #21Member
- Join Date
- Apr 2015
- Location
- Blenheim, New Zealand
- Age
- 78
- Posts
- 55
I think I'm pointing out the obvious here Gents. The reason it looks like the lines taper across the length of the wave is because they do taper across the length of the wave. Print off the diagram and measure it, or even measure it on the screen and you will see there's quite a pronounced taper.
Rex
-
30th July 2017, 04:31 PM #22
As I mentioned earlier, making a lid pattern this way you finish up with two lid patterns.
This is the second box made using the design and in this instance I varied the depth to allow the leg features to be cut. This box was made with internal splines on the mitred corners.
wb#2.JPGwb#1.JPGwb#3.JPGAnd my head I'd be a scratchin'
While my thoughts were busy hatchin'
If I only had a brain.
-
31st July 2017, 09:46 AM #23Member
- Join Date
- Apr 2015
- Location
- Blenheim, New Zealand
- Age
- 78
- Posts
- 55
Very nice Ruddy (again). The paper lining in the lid, I assume it is paper, is quite unusual and very effective - a striking contrast to the rest of the box.
Also unusual is the false lift on the front and my guess is that the magnets are so strong that you need to hold the box down when you lift the lid.
Rex
-
15th August 2017, 04:22 PM #24Member
- Join Date
- Apr 2015
- Location
- Blenheim, New Zealand
- Age
- 78
- Posts
- 55
Well I finally got around to building a box with the wave lid. This time I cut the pieces with my coping saw (not the right tool for the job) which showed me how far from being skilled I actually am. I used veneers about 2 mm thick and hand fitted them individually using sanding blocks - a lot of work but it's hard to stop this kind of project once you get started. Ultimately the finished product doesn't look too bad although I'd rate it as a workmanlike rather than an outstanding job.
IMG_3628.jpg IMG_3641.jpg IMG_3634.jpg IMG_3635.jpg
Visually, Ruddy's design works very well and the 3D effect is quite striking, especially when viewed from the front, as in the first two photos. As seen in the third photo I have yet to find a suitable lining for the inside of the lid, this shot showing the wooden hinge I used. The last shot shows the hinge from the back and this photo does my head in. If I study it for a while it looks like the lid is inverted and leaning towards me - altogether too much visual conflict.
The box is made from Matai with the lid veneers being Totara and Kahikatea (kiwis will know what I'm talking about) and it measures 210 x 130 x 56 mm, finish is Danish oil. I didn't try to add any shading but I should have learn't from my earlier experiments and just waxed the top as the oil showed up every little defect and highlighted the grain, slightly to the detriment of the 3D appearance. A woodworker friend suggested I should have used wood with a curve in the grain to match the curve of the wave - there's a challenge for someone!
Thanks for the idea Ruddy, after making this I have certainly gained a lot of respect for your skills.
Rex
-
15th August 2017, 05:11 PM #25
Its a great optical illusion.
I wonder how some of these static images would go (click to open up):
c22389208a8ace15b5dbadac23941197--moving-optical-illusions-circles.jpg maxresdefault.jpg optical-illusions-2.jpg
-
15th August 2017, 06:01 PM #26Member
- Join Date
- Apr 2015
- Location
- Blenheim, New Zealand
- Age
- 78
- Posts
- 55
DavidG - Thanks for that, changes made. Is there some way to remove the errant post completely?
WoodPixel - That way madness lies, especially the first one - although the second one is strangely appealing!
Rex
-
15th August 2017, 06:34 PM #27
Hi Rex,
Congratulations on the wave box. I found that some subtle shading on the light coloured pieces really enhances the 3D effect. As someone mentioned above, some controlled hot sand shading on the light coloured wood would enhance the illusion.
If you look at some of my earlier posts you will see that I am a big fan of wooden hinges and your hinges are so well done.I appreciate the work you have put in to achieve that look where the wooden hinges become an integral feature of the design.Nice work indeed.And my head I'd be a scratchin'
While my thoughts were busy hatchin'
If I only had a brain.
-
16th October 2017, 01:53 AM #28Member
- Join Date
- Jan 2008
- Location
- Central, Michigan, U.S.A.
- Posts
- 94
WoodPixel I have taken a class with Patrick Edwards and you are right he does some amazing work. In his class we used a Chevalet and I also built one for my shop at home as well. Using a Chevalet is totaly different and easier to use than using a hand saw as the Chevalet has a fixed articulating arm that gives you much more control than a hand saw. But you are right with some practice you can use a hand saw with positive results
-
16th October 2017, 09:02 AM #29
I admire their work. They are on my facebook feed for the very limited posts they do and I often check their sites. I've learned a great deal from careful observation of the image and rereading text 20 times
-
2nd January 2019, 05:31 PM #30
Finally found that round tuit! Unfortunately it didn't work as far as the illusion goes at all Don't know if it is the growth rings or the lack of tapers from one side to the other or both but it just looks flat from any angle. Ah well , it was worth a try.
Similar Threads
-
The wave
By IDEFIX in forum WOODCARVING AND SCULPTUREReplies: 3Last Post: 28th December 2015, 08:35 AM -
Wave Cabinet
By hiroller in forum WOODWORK - GENERALReplies: 6Last Post: 3rd October 2015, 02:20 PM -
Wave Grooves
By Fredo in forum WOODTURNING - GENERALReplies: 19Last Post: 5th April 2012, 09:11 AM -
Mr Sheen's Wave...
By rod1949 in forum HAVE YOUR SAYReplies: 1Last Post: 14th November 2008, 10:43 AM -
Wave to me.
By outback in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 6Last Post: 5th February 2006, 11:28 AM