Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 17
Thread: Domino wannabe & Mortise Jig
-
3rd October 2022, 12:40 PM #1Member
- Join Date
- Dec 2008
- Location
- Sydney
- Posts
- 72
Domino wannabe & Mortise Jig
I saw a jig on facebook marketplace and got half way through buying it when I realised it was probably too cheap to be true.
(Tianli router jig will find it if curious)
It was advertising at $50 on fb, after a bit of website checking and searching for the real thing in other markets it retails more like $200.
Not a risk I was willing to take, though I may still take a plunge on a legit source down the track.
Tianli.jpg
I am however a little obsessed with my cordless trimmer router and loved the thought of doing something similar, it already has a plunge base which operates better than most but comes with a really crappy edge guide.
Below are the photos of where I am up to - I will give it a test drive later today.
In for a penny in for a pound I decided I could keep going and run a few jigs off the one idea - total cost around $45 for all three and rods - the screws I already had.
If you want to make similar
- 8mm stainless rods (I'm against all things that rust easily where I can avoid it)
- 25mm square Al for the rod block slides - I made them a little oversize to fit my other router as well and yes they could be trimmed down (second set of holes in pic)
- 100 x 6mm angle Al for the guides (I may make a corner reinforcement for the big one - Al fences do bend if dropped
Tooling; drill press, hack saw, cordless drill for tapping (I am lazy and the cordless does an excellent job if you are not heavy handed)
I did cheat and used a vertical mill to clean up the throat of the bigger one but you can get by without.
I'm happy to draw up plans if anyone is interested but it isn't brain surgery.
Still need to add a front handle and buy some screw knobs for locking to the rods
Domino.jpg
MortiseJig.jpg
Well - the first test worked a treat - the reason I went down this rabbit hole was a pesky break in one of our parker era dining chairs.
The tenon was snapped and more or less needed a domino type tenon replacement.
The guide edge served as the platform from the bench top and the fence plates kept the piece centred, made a tricky job easy.
Before.jpg
Drawings for others are always problematic - too much too little??
The basics are here - the holes in the throat are 4mm by design, this gives a centre reference and the edges for an 8mm cutter
Domino Plate Drawing .pdf
-
3rd October 2022 12:40 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
3rd October 2022, 01:40 PM #2Senior Member
- Join Date
- Jun 2012
- Location
- Dungog
- Posts
- 274
Well done, simple things are often the best.
Plans , yes please.
Again thanks and simply the best.
-
3rd October 2022, 02:12 PM #3
+1 for plans please
Would you consider making it to sell, I have a very strong feeling that your on a winner hereThe person who never made a mistake never made anything
Cheers
Ray
-
3rd October 2022, 03:18 PM #4Senior Member
- Join Date
- Jan 2005
- Location
- Campbelltown NSW
- Age
- 77
- Posts
- 335
Clever thinking. That design makes me think that the angle and block could be made as one part on the 3D printer. Locking the steel rods securely could be tricky but achievable I think.
-
3rd October 2022, 08:54 PM #5Member
- Join Date
- Dec 2008
- Location
- Sydney
- Posts
- 72
Last time I 3d printed anything near this size it took forever and warped a lot and also provided a few bird nests, good luck
I can add the diagonal ribs and send an stl file if you are that crazy - the threads would probably be better as a captured nut, I can envisage it but you can draw it
-
3rd October 2022, 09:21 PM #6Member
- Join Date
- Dec 2008
- Location
- Sydney
- Posts
- 72
Honestly - I'd rather share the plans, share the love.
To monetise this would be a chore.
It's probably more than a few hours all told, on a small scale I'd be charging between 200-300 before it would be worthwhile, I don't think the market would bear that when you can make your own with a drill press and $45 material. Pay a few more dollars and the Al seller will do all the length cutting (I do have access to a cold saw which sped things up immensely)
If you do make your own, accuracy is everything but there is a simple cheat - clamp parts together, drill through at 5mm, separate parts then tap the square bar, drill angle out to 6mm and countersink. The holes could be anywhere and it will still align correctly together. The same can't be said for the slide holes - these were a pain.
I thought the gap from plate was the same on the other router and even checked it twice - still wrong.
Now I need a shim packer to switch between routers - I'll live. (I think the dimensions provided are now correct)
-
4th October 2022, 09:40 AM #7
Thank you for plans x10
The person who never made a mistake never made anything
Cheers
Ray
-
4th October 2022, 12:19 PM #8Senior Member
- Join Date
- Jan 2005
- Location
- Campbelltown NSW
- Age
- 77
- Posts
- 335
Thanks for the plans. This gives me an opportunity to practice with Fusion360. I had thought of an encapsulated nut or a slot for a square gutter bolt nut.
Another thought was using a threaded rod with inner and outer nuts which may be more secure than a clamping screw on a rod and easier construction. Probably more fiddling though setting up in practice.
I agree that prints can take time but the advantage is that I can be doing other things while it’s working.
-
4th October 2022, 12:39 PM #9Member
- Join Date
- Dec 2008
- Location
- Sydney
- Posts
- 72
Fusion was where I did my retrospective drawing, consider bringing the lock nut in from the side, then the captured nut can drop in a vertical slot.
You can also trim out a lot of bulk and add ribbing to bring the stiffness up.
I've come up with a cleverish way of adding an aluminium diagonal brace for metal version, will post when it is done.
-
4th October 2022, 06:22 PM #10Member
- Join Date
- Dec 2008
- Location
- Sydney
- Posts
- 72
I was pondering how to clamp a 45 degree edge into a corner when it all became obvious.
Clamp a square into the corner, do all the tap size drilling together on one end (label carefully).
Flip it over and do the same for the other end.
Cut the thing in half at 45 degrees, then do the tapping, clearance hole drilling and countersink.
Here I've used 80 x 10 flat bar just because I have some kicking around.
I milled the hell out of it until it was square because the 100mm angle Al is not square or flat.
This will pull it all into shape and hopefully hold it there.
Brace.jpg
-
6th October 2022, 01:28 PM #11Member
- Join Date
- Dec 2008
- Location
- Sydney
- Posts
- 72
More or less finished
Fwiw I shimmed for the festool with .8mm Aluminium flashing - again because I had it kicking around, it's super easy to cut and won't create a galvanic reaction on this jig. Seems to be right for festool now. 10mm is still fine for makita trimmer plunge base.
Good luck measuring 10.8mm if making for this router.
Keep in mind the holes are a little oversize so they slide, this also means a little pull in when the lock nuts are tightened. These offsets allow for it.
My 6mm spiral upcut also arrived today along with 8mm collet for trimmer router.
Just waiting for plastic knob locking screws and should probably add a handle or hold down knob.
It has also dawned on me that if you wanted a mini router table for small pieces, the domino wannabe has you covered, just need a throat insert.
Braced1.jpg Braced2.jpg
-
7th October 2022, 05:50 PM #12Senior Member
- Join Date
- Jan 2005
- Location
- Campbelltown NSW
- Age
- 77
- Posts
- 335
I was thinking much along the same lines. I initially had the slot horizontal, parallel with 8mm hole but from the top leaves a bit of meat around the entry exit points of the 8mm hole, although I don't think it matters that much as the rod is being pushed away from that those points. I added braces mainly to stop flexing as that could be an issue with the material. The 3D model can be viewed here.
I made a couple of blocks to test the clamping strength and after applying way to much force the 10% infill one started to compress the material (PLA+) but the 35% infill one stayed solid.
IMG_5862.jpg IMG_5861.jpg
Now, I haven't printed the model mainly because I haven't got a Makita to test for fit and practicality and with the settings I'm using it is a 36 hour print for each side which is not an issue.
-
9th October 2022, 09:40 PM #13Member
- Join Date
- Dec 2008
- Location
- Sydney
- Posts
- 72
Not too bad, the power of 3D printing is doing the things that are painful by regular means
I've sketched on your model where you could easily thin to a web, all lumpy corners can be radiused, no strength reduction but a fair bit of plastic and time saved.
Internal corners radiused will substantially add strength
In between the diagonal braces you could add a dust extraction port - or slides to accept a separate printed part
Domino Plate_snapshot(1).png
-
10th October 2022, 02:17 PM #14Senior Member
- Join Date
- Jan 2005
- Location
- Campbelltown NSW
- Age
- 77
- Posts
- 335
Thanks, I had considered the option of internal fillets and initially was going to print on the edge to save on supports, however when the throat was added I added the braces and removed them. What takes time is the support build for the the clamping block which adds around 10 hours at the current print speed of 40mm/s.
To do away with the supports, I am considering printing the clamping block separately with threaded holes and attach to the top plate with screws (and glue?) and push the print speed up a little which altogether will cut the print time to almost in half.
-
10th October 2022, 05:39 PM #15Member
- Join Date
- Dec 2008
- Location
- Sydney
- Posts
- 72
Add a dovetail slide joint to the plate and screw block, if ABS then smear with acetone, slide it in and it will never move again - would look awesome in two tone.
Similar Threads
-
Angled mortise with domino
By qwertyu in forum WOODWORK - GENERALReplies: 4Last Post: 16th July 2019, 11:45 AM -
Woodworker wannabe intro
By craftyCAD Cam in forum G'day mate - THE WELCOME WAGON -Introduce yourselfReplies: 9Last Post: 4th December 2011, 12:52 AM -
A Newbie Wannabe Scroller
By Revlis in forum INTARSIAReplies: 3Last Post: 29th August 2007, 06:13 PM -
Tests for Wannabe Parents
By Felder in forum WOODIES JOKESReplies: 4Last Post: 20th February 2007, 06:09 PM -
Mortise and Tenon v Domino
By Flowboy in forum FESTOOL FORUMReplies: 0Last Post: 29th July 2006, 04:06 PM