Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
31st March 2023, 12:22 PM #1New Member
- Join Date
- Mar 2023
- Location
- Australia
- Age
- 40
- Posts
- 4
I think i've made a grave mistake
I have been creating this table for the past couple of weeks (I am new to woodworking) and I finally stained and vanished (1 round) and the wood has come up like this? What happened? It was nicely smooth and sanded before.
20230330-204559 hosted at ImgBB — ImgBB
-
31st March 2023 12:22 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
31st March 2023, 01:26 PM #2SENIOR MEMBER
- Join Date
- Nov 2010
- Location
- Perth W.A
- Posts
- 720
Did you use an oil based stain and water based varnish ?
-
31st March 2023, 02:27 PM #3New Member
- Join Date
- Mar 2023
- Location
- Australia
- Age
- 40
- Posts
- 4
I used Feast Watsons ProofTint Spirit based interior stain and the Feast Watson Satin Clear Varnish
-
31st March 2023, 03:31 PM #4SENIOR MEMBER
- Join Date
- Nov 2010
- Location
- Perth W.A
- Posts
- 720
Was the proof tint fully dry before applying the varnish ?
Looks like some kind of strange interaction has taken place.
Do you know what wood species you used ?
-
31st March 2023, 03:47 PM #5New Member
- Join Date
- Mar 2023
- Location
- Australia
- Age
- 40
- Posts
- 4
I did wait for it to dry fully and then applied the varnish 5 days later.
Okoume hardwood timber is the timber I used. You are right, it's a weird interaction.
-
31st March 2023, 06:19 PM #6GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
Okoume is often very high in silica. This will cause surface defects like tiny bubbles appearing under the first finish coats of varnish have been applied, particularly if left in the sun to dry. Sand back to a good surface and refinish. May take a few coats to settle down but should come good next time round. Problem can also be caused by silicon spray being used on machinery (planer) as a lubricant during dressing of the timber.
-
1st April 2023, 12:29 PM #7New Member
- Join Date
- Mar 2023
- Location
- Australia
- Age
- 40
- Posts
- 4
Amazing, thanks for the advice. I'll try sand back and try again, is sanding after varnish relatively easy?
-
2nd April 2023, 11:20 PM #8
Afraid not. The varnish clogs up the sandpaper. A card scraper or a Stanley 80 would get it done quicker.
Other option is paint stripper. Brush on and it softens up the varnish making it easy to get off with a scraper. Then its sanding again for next try.
Regards
John
-
3rd April 2023, 05:11 PM #9GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,559
You dont need to remove the varnish completely. In fact, you want to keep the surface sealed to prevent more silica coming to the surface and causing the same problem again. Only sand to an extent that removes the blemishes, not back to the timber. Use an anti clog sand paper, this will help with varnish retention. Not perfect but it does help.
Similar Threads
-
I made a BIG mistake
By SAISAY in forum METALWORK FORUMReplies: 5Last Post: 5th May 2012, 08:30 PM -
Made the mistake of dropping into the Festool stand at the TWW Show
By scottbr in forum FESTOOL FORUMReplies: 13Last Post: 9th July 2011, 09:30 AM -
Have we made a mistake??
By HazzaB in forum WOODTURNING - PEN TURNINGReplies: 7Last Post: 24th August 2009, 09:04 AM