Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Supplies for lap steel
-
8th August 2011, 11:11 PM #1
Supplies for lap steel
Hi all,
Been a while since I was here, and had a few non-starts at instrument building. Hopefully this time I can get my act together and make progress - life seems a bit more balanced now. Plus I've started learning the banjo so feeling a bit more musically inclined
Anyway, with the banjo influence and narrowing down my interest in "what to play and learn" I'd like to give a lap steel a go. But being a leftis, the commercial choices are limited.
So, along comes the motivation to build one.
I'd lime any recommendations for suppliers of parts (in Melbourne or mail order) where I can get lap steel parts - and plans too (they can be right handed as I can just 'flip' them).
Thanks in advance - I know I could just do a web search but would prefer someone local and recommended by the more accomopiates holders here.
Thanks in advance.
Regards,
Darren
-
8th August 2011 11:11 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
9th August 2011, 09:09 AM #2Member
- Join Date
- Nov 2010
- Location
- NSW
- Posts
- 64
A left handed lap-steel would be no different to a right handed one. The strings would need flipping and so would the saddle and nut.
Tasmanian tone woods will have you covered for wood. AMS will have the rest.
If not LMII or stew mac.
-
9th August 2011, 12:14 PM #3
Hi Lux,
Thanks fo the AMS suggestion - I wasn't aware of them so just what I was after. Planning on Tassie Tonewoods or Mathews Timber for the blank, just need the shiny bits and prefer a local supplier.
I plan to get a standard lap steel plan and flip it, which is easy enough. However hard to buy one as although I thought of restringing a RH one, the control knobs would probably get in the way of playing so less risky to start from scratch.
Thanks,
Darren
-
9th August 2011, 12:47 PM #4Member
- Join Date
- Nov 2010
- Location
- NSW
- Posts
- 64
Sorry TK1, I mis understood what you wanted.
I thought you meant a weissenborn, which is a symmetrical acoustic instrument.
I didnt realise you were talking solid body I understand now about the controls etc. For pickups look at Brierley Guitar Pickups Home Page I just seen a lap steel build with one of his P-90s. A p90 and humbucker would be pretty cool.
Tassie tonewoods is probably your best bet. A solid blackwood (assuming that what you will use) would be quite heavy, so you might want to do a two piece body and route out some chambers.
-
9th August 2011, 06:23 PM #5Senior Member
- Join Date
- Sep 2007
- Location
- Caves Beach, NSW
- Posts
- 277
Well using a standard plan may or may not be the best way to go.
Most of the old lap steels were designed for a C6 tuning which is good for hawaiian music or western swing.
They generally were a 22.5 inch scale.
For tuning to open E or D a 25" scale like a weissenborn works better
Drawing up your own design around this scale length is pretty easy .
-
9th August 2011, 06:30 PM #6Senior Member
- Join Date
- Sep 2007
- Location
- Caves Beach, NSW
- Posts
- 277
Check out Asher Lap steels
Lap Steel Guitars - Custom made in California by Luthier Bill Asher
-
9th August 2011, 07:33 PM #7Member
- Join Date
- Nov 2010
- Location
- NSW
- Posts
- 64
They are nice looking weissenborns Jeff.
Here are a few more pics, these two are ebony fingerboards, the rest is blackwood these two are sold but there is two more here. The two new ones have a blackwood fretboard and it looks alot better it helps when the figure is all time.
-
11th August 2011, 11:05 PM #8
Hi,
Thanks again Lux - I should have been more specific that I intended to do an electric build.
Jeff - thanks for the scale length advice, I'll need to look at that.
I'd like to do an acoustic eventually but plan to start off with an electric first as although it has the electronic aspect, it will be a quicker and easier overall build without worrying about a hollow body acoustics and building - that's my view anyway! )
Thanks again,
Darren
Similar Threads
-
Q's on pen supplies
By new_guy90 in forum WOODTURNING - PEN TURNINGReplies: 18Last Post: 19th January 2009, 02:14 PM -
Where do you get your supplies from??
By Strungout in forum MUSICAL INSTRUMENTSReplies: 3Last Post: 21st August 2006, 10:37 PM -
steel supplies
By mako in forum METALWORK FORUMReplies: 2Last Post: 11th May 2006, 12:05 AM -
Triton Steel Cutter and DIY steel tubes
By Intheshed in forum TRITON / GMCReplies: 51Last Post: 6th January 2005, 12:56 AM