Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
-
11th August 2010, 11:46 AM #1Intermediate Member
- Join Date
- Mar 2009
- Location
- Brisbane
- Posts
- 33
How To Thickness the Back of a Headstock ... ?
Hey Guys,
I've been making a Strat, as a learning exercise, and I've nearly finished that build (lots of mistakes - good learnings!!). I bought a neck for that build.
However, I'm turning my mind to my next build, in which I want to make a neck. I'm thinking of an angled headstock, and I've seen plenty of posts about that. I'm thinking of a one-piece, rather than a scarf joint, and I've seen a post on Project Guitar (I think it was) about how to do an angled headstock (the front face) on a jointer.
But I haven't seen anything about how to thickness the back face of such a one-piece angled headstock. I think it will need to be about 10-12mm thick, depending on the length of the tuners, and I can't think how to do it. Maybe I need to make some sort of a jig to clamp the headstock flat (with the rest of the neck sticking out in mid-air) and run over the back with a router?
Has anyone got any ideas or photos?
Thanks.
-
11th August 2010 11:46 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
11th August 2010, 01:43 PM #2Senior Member
- Join Date
- Sep 2007
- Location
- Sydney
- Posts
- 489
Hi CT,
This is how I thickness a headstock. I set up a flat board which is held above the bench to parralell to the surface. I do this by clamping a sheet of 16mm mdf sitting on some slats. Assuming you have a flat face on the headstock, clamp it face down to the bench. Using a router, set the bit depth such that it is clear of the bench by the desired thickness of the headstock and run it over the back of the headstock, producing a clean flat parrallel surface. See pic below.
I will rout in severall passes to final thickness up to the start of the volute. The curve iof the volute I cut by hand using a coping saw and sand to final curvature very, very carefully with a drum spindle sander in the drill press.
Cheers
Peter
-
11th August 2010, 05:06 PM #3
I use my faithful Safe-t-planer,
"We must never become callous. When we experience the conflicts ever more deeply we are living in truth. The quiet conscience is an invention of the devil." - Albert Schweizer
My blog. http://theupanddownblog.blogspot.com
-
12th August 2010, 11:04 PM #4
Like Seb says...Safe-T-planer the easiest way.
Whatever note you blow youre never more than a semitone away from the correct one....(Miles Davis)
Similar Threads
-
Headstock oil caps
By MarkJ in forum THE HERCUS AREAReplies: 2Last Post: 13th November 2009, 09:59 PM -
Headstock handwheel
By Woodwould in forum WOODTURNING - GENERALReplies: 4Last Post: 24th January 2009, 08:07 AM -
Stiff headstock
By lubbing5cherubs in forum WOODTURNING - GENERALReplies: 9Last Post: 22nd December 2008, 08:25 PM -
Rocking Headstock
By lubbing5cherubs in forum WOODTURNING - ORNAMENTAL TURNINGReplies: 32Last Post: 17th December 2008, 10:57 PM -
Headstock flex
By Tiger in forum WOODTURNING - GENERALReplies: 29Last Post: 16th November 2006, 11:27 AM