Hi RC
sounds like we need a show us your tool and cutter grinder thread :2tsup:
cheers
Harty
Printable View
Hi RC
sounds like we need a show us your tool and cutter grinder thread :2tsup:
cheers
Harty
Here we have the TC grinder accessories I have...
It includes...
motorised workhead, dividing plate for workhead, angular adjustment thingie for setting relief on the cutter, centring gauge, diamond dresser, universal vise, plus some spare bits for it, two sets of centres, grinding wheel arbours, extended grinding wheel arbours, an attachment for sharpening form cutters like gear cutters and an internal grinding attachment that is currently disassembled but all the bits for it are not shown in the photo as they are stored away...
Then I have a air spindle, radius attachment and universal vice for the little TC grinder..
Hi .RC,
Very impressive collection, I wish I knew what I was looking at... :) It will take me a while to figure out what is what...
What wheels do you mostly use?
Regards
Ray
Just cup wheels...
Hi .RC,
What's the cream coloured thing that looks like a rocket launcher?
https://www.woodworkforums.com/attach...sories-009.jpg
Looks big for an air spindle?
Regards
Ray
Hi .RC,
I have no idea what this is?
https://www.woodworkforums.com/attach...sories-007.jpg
Regards
Ray
Edit... Oh wait is that part of a dog?
Hi Ray
we have had a scraping course to get us started with the basics
now we need a tool and cutter course to get the basics of that
Cheers
Harty
Hi Harty,
I reckon Rocky would be a good place to hold it... pity it's so far from the center of the universe though... :D
I did find a lot of Walter setup documentation on-line, that goes into a fair amount of detail on angles and setup procedures. There is a lot of detail to learn.
Have you got a list of what you want from sopko?
Regards
Ray
Hi Ray
No list
been looking and I need to do some more research before i jump in and order the wrong parts so dont wait for me
cheers
Harty
That is the air spindle.... it is not that big..It takes 5C collets...
This is what you need
Tool and Cutter Grinder CD, Model Engineer? Buy It Now | eBay
I have a copy, it is quite good...
Hi .RC,
Thanks for that I've ordered the cd. Looks like just what I need. :2tsup:
I'm currently just cleaning up around the wheel head, (while waiting for bearings to arrive) and getting paint off the oil caps that were painted over, and notice that a lot of the reference surfaces have been painted over as well, so I'm gradually getting the paint off those as well.
Do you have a picture of your wheel head?
Regards
Ray
Well, it''s almost back together...
Here is the cross slide screw arrangement, for future reference. New timken tapered roller bearings.
http://www.backsaw.net/pics/TC/DSCN1786.JPG
The repaired pin on the cross slide nut.. a bit of thread lock on the grub screws. The pin is a nice tight press fit into the nut.
http://www.backsaw.net/pics/TC/DSCN1787.JPG
The saddle is back on, the screw is fitted after the saddle goes back.
http://www.backsaw.net/pics/TC/DSCN1789.JPG
New bearings for the table guides... Phil, I measured the rollers, and the front rollers were 11.603 +-0.001 and the back rollers were 11.711+-0.001 I didn't check every single roller, just about 10 or so around the chain.. seemed pretty consistent.
Can't think why the front and back would be different..? Also started filling the base of the table with oil. There are oil wicks going down to the cross slide ways from the table reservoir.
http://www.backsaw.net/pics/TC/DSCN1790.JPG
The table is back on, and ready for a clean up with scotch brite.
http://www.backsaw.net/pics/TC/DSCN1791.JPG
Next job is a proper clean up.. all the handles etc..
Regards
Ray
Here's a safety tip for anyone restoring old machine tools...
I pulled the spindle motor and the workhead motor out to get my SIL to rewire them for delta. As soon as I touched the wires the insulation crumbled to dust.
If I had powered it up.. zap!...
Lucky. :2tsup:
Regards
Ray