Search:
Type: Posts; User: Flathed
Search: Search took 0.00 seconds.
-
5th December 2017, 07:28 AM
Thread: Tailstock problem, any ideas?
by Flathed- Replies
- 12
- Views
- 1,320
Thanks Paul for the suggestions.Between that and...
Thanks Paul for the suggestions.Between that and China's diagram was finally able to remove the top pin and rotate the barrel till the screws lined up with the handwheel hole.The barrel is now out...
-
4th December 2017, 10:38 AM
Thread: Tailstock problem, any ideas?
by Flathed- Replies
- 12
- Views
- 1,320
Thanks China,when I got the lathe had no manuals...
Thanks China,when I got the lathe had no manuals etc with it.Hopefully can get the little pin out of the top of the tailstock.No luck yet.At worst will drill through handwheel to get screwdriver to...
-
3rd December 2017, 07:13 PM
Thread: Tailstock problem, any ideas?
by Flathed- Replies
- 12
- Views
- 1,320
Sorry guys,should have put these in...
Sorry guys,should have put these in first425187425189425191425192
-
3rd December 2017, 04:04 PM
Thread: Tailstock problem, any ideas?
by Flathed- Replies
- 12
- Views
- 1,320
Tailstock problem, any ideas?
Was wondering if anyone can help.Was using lathe yesterday without any problems.Its an older type Elu I got second hand ,but has been working well for past two years.Went to adjust tailstock today...
-
30th January 2017, 07:45 PM
Thread: What timber is it
by Flathed- Replies
- 9
- Views
- 1,370
Limited information
Thanks for the help guys.Old neighbours moved, so cant get any help from them.I havent dealt with white cedar before,but this timber is a lot harder than any red I,ve ever seen.All the trees were...
-
27th January 2017, 06:51 PM
Thread: What timber is it
by Flathed- Replies
- 9
- Views
- 1,370
Mystery timber
Unfortunately they have been dead for a while,so no leaves,flowers seeds etc.Hope the end grain and bark pictures might be useful.405014405013
-
25th January 2017, 08:52 PM
Thread: What timber is it
by Flathed- Replies
- 9
- Views
- 1,370
What timber is it
Can anybody help me identify a timber I have been turning for a couple of years.Live near Bowraville ,NSW,and there were 5 dead trees on the boundary with neighbours. About 200mm at base,approx 10...
-
4th June 2015, 08:51 PM
Thread: Is it suitable?
by Flathed- Replies
- 1
- Views
- 857
Is it suitable?
Have been given three trunk slabs of what is known as "watermelon tree"(Syzgyium Moorei) by my boss who had to have the tree cut down.They are about 600 mm diam by 75mm thick.Looked it up and its a...
-
3rd October 2013, 09:19 PM
Thread: How suitable
by Flathed- Replies
- 7
- Views
- 1,399
Thanks
Thankyou for the info.Yes I have access to heaps of Camphor Laurel round here and have had reasonable success with it so far .There is also the problem that I havent mastered the razor sharp edge...
-
3rd October 2013, 09:13 PM
Thread: How suitable
by Flathed- Replies
- 7
- Views
- 1,399
Wonderful
Thanks gives me something to look forward to if I get some.
-
2nd October 2013, 09:17 PM
Thread: How suitable
by Flathed- Replies
- 7
- Views
- 1,399
How suitable
Hi there,as a relative newcomer to the lathe I was wondering if anyone can tell me whether Illawarra Flame is suitable for turning.I have access to a freshly felled tree but dont want to store a lot...