Search:
Type: Posts; User: Froggy10
Search: Search took 0.00 seconds.
-
12th December 2017, 04:43 PM
Thread: West System Use?
by Froggy10- Replies
- 29
- Views
- 2,396
For best results I used to mix by weight. ...
For best results I used to mix by weight. Depending on the angle the measurement may appear to be correct or to little/to much. This also will help remove any doubts of improper mixing.
Sent... -
11th December 2017, 03:40 PM
Thread: Removing rust from
by Froggy10- Replies
- 44
- Views
- 6,432
This is what I do. Works like a charm Sent...
This is what I do. Works like a charm
Sent from my SM-G935W8 using Tapatalk -
11th December 2017, 03:38 PM
Thread: Help needed with FW Floorseal finish
by Froggy10- Replies
- 4
- Views
- 780
I used it and found it to be frustrating too. I...
I used it and found it to be frustrating too. I was Appling with a bristle brush. I then switched to foam. Let it harden and then sand down. Apply again with the foam brush but apply a thin...
-
5th December 2017, 03:39 PM
Thread: In need of some advice
by Froggy10- Replies
- 18
- Views
- 4,763
I actually did take that into consideration Lol....
I actually did take that into consideration Lol. I did completely forget about the expansion until you guys mentioned it. Then it all came back to me..... it been 10 yrs since I have actually built...
-
5th December 2017, 11:41 AM
Thread: JJ - Rugby (2017)
by Froggy10- Replies
- 40
- Views
- 2,605
Absolutely stunning, detailed and talented ...
Absolutely stunning, detailed and talented
Sent from my SM-G935W8 using Tapatalk -
5th December 2017, 10:27 AM
Thread: In need of some advice
by Froggy10- Replies
- 18
- Views
- 4,763
Table top is solid birch Legs are laminated...
Table top is solid birch
Legs are laminated plywood with birch veneer.
Base is solid birch
Skirt is laminated with a veneer.
The support is just a piece of spare mdf that I screwed downward into... -
5th December 2017, 05:06 AM
Thread: In need of some advice
by Froggy10- Replies
- 18
- Views
- 4,763
So here is the (almost)completed project. I...
So here is the (almost)completed project. I still have to sand and buff. Ran out of propane in the middle of the night and of course it was the only night in the last couple of weeks to go below...
-
3rd December 2017, 02:28 AM
Thread: In need of some advice
by Froggy10- Replies
- 18
- Views
- 4,763
So I decided to go a different route after...
So I decided to go a different route after everyone feedback. I am in the process of laminating 2 half pieces to form the skirt. I am going to attach with cleats and male the circumference small to...
-
1st December 2017, 05:33 AM
Thread: In need of some advice
by Froggy10- Replies
- 18
- Views
- 4,763
The skirt is to make the table top to appear...
The skirt is to make the table top to appear thicker and conceal the panel that is stabilizing the legs. If it needs to be moved I just have to take the tabletop off and only move 2 pieces. ...
-
30th November 2017, 04:59 PM
Thread: In need of some advice
by Froggy10- Replies
- 18
- Views
- 4,763
Thanks for the advice. It is solid wood.... I...
Thanks for the advice. It is solid wood.... I may want to rethink this......?????
Sent from my SM-G935W8 using Tapatalk -
30th November 2017, 03:39 PM
Thread: In need of some advice
by Froggy10- Replies
- 18
- Views
- 4,763
It is end grain to end ģrain. Once I make the...
It is end grain to end ģrain. Once I make the ring I was going to glue the edge to the underside (face). I was then going to run the router tracing the edge of the table. I am currently trying to...
-
30th November 2017, 04:53 AM
Thread: In need of some advice
by Froggy10- Replies
- 18
- Views
- 4,763
In need of some advice
I am in the process of building a table and I am having trouble with the skirt. I choose to do the skirt with segments because I have never steam bent wood before and figure this wasn't the project...