Search:
Type: Posts; User: raycon
Search: Search took 0.00 seconds.
-
12th December 2020, 10:07 AM
- Replies
- 21
- Views
- 1,819
Poll: A.C.T. I’m very interested, but what is freight to Perth...
I’m very interested, but what is freight to Perth like?
-
12th August 2020, 01:19 PM
Thread: Metabo TS254 vs Dewalt DW745
by raycon- Replies
- 19
- Views
- 21,718
Hi Ozmike, I understand the DeWalt takes a...
Hi Ozmike, I understand the DeWalt takes a variety of blades but I haven’t yet tried any others. It certainly should take a dado set because the arbor is big enough, but again, what width I can’t...
-
4th May 2020, 02:25 PM
Thread: Metabo TS254 vs Dewalt DW745
by raycon- Replies
- 19
- Views
- 21,718
Out-of-the-box
I recently bought a Dewalt DWE7491-XE (two dustports and I'm using it in an inside-the-house workshop) and I have been very impressed with its accuracy. The rip fence with rack-and-pinion adjustment...
-
4th May 2020, 01:53 PM
Thread: Bandsaw Adjustment Needed?
by raycon- Replies
- 12
- Views
- 1,030
Gentlemen, the blade. It's all about the blade. ...
Gentlemen, the blade. It's all about the blade. Chris is spot on about the OOTB blade. It's only 9mm wide. The 3 and 6 TPI blades I bought are 12.5 mm ( except for the 3mm I bought specifically...
-
4th May 2020, 11:56 AM
Thread: Bandsaw Adjustment Needed?
by raycon- Replies
- 12
- Views
- 1,030
Thanks to all
Can't thank you all enough. Bad picture, but this is the result of simply properly aligning the blade on the top wheel, and cutting more slowly. Same blade. I also checked the fence alignment and...
-
4th May 2020, 11:42 AM
Thread: Bandsaw Adjustment Needed?
by raycon- Replies
- 12
- Views
- 1,030
Thanks Chris, I did buy some more blades, of...
Thanks Chris, I did buy some more blades, of various TPI, but from H&F so not sure if they'll be any better. However I have had some success with the adjustments. See next post.
-
4th May 2020, 09:22 AM
Thread: Bandsaw Adjustment Needed?
by raycon- Replies
- 12
- Views
- 1,030
So, thank you all for the mass of information. ...
So, thank you all for the mass of information. This gives me much to try, and I'll work through it all. FYI the blade is brand new, and seems to have a coating on it which is rubbing off on the...
-
3rd May 2020, 07:28 PM
Thread: Bandsaw Adjustment Needed?
by raycon- Replies
- 12
- Views
- 1,030
Bandsaw Adjustment Needed?
Hi All, I've been a member for a while but this is my first post, so my apologies in advance if I break a rule or miss something out.
I'm also a newbie woodworker, and have just acquired my first... -
26th September 2018, 09:49 AM
Thread: Sheoak blanks for box making
by raycon- Replies
- 2
- Views
- 2,668
WEST AUST Hi Dusteater, may I have these please?
Hi Dusteater, may I have these please?
-
1st September 2018, 03:50 PM
Thread: Gpo's in the slab.
by raycon- Replies
- 20
- Views
- 4,863
I have had GPO's on the floor, and in the boxes...
I have had GPO's on the floor, and in the boxes with lids. You tend to kick them, you can even kick the plug out or the switch off at a crucial point in some process. And you can never shift them. ...
-
24th July 2018, 05:44 PM
Thread: Lace sheoak blanks for box making
by raycon- Replies
- 6
- Views
- 1,816
WEST AUST Do you do this often dusteater? I’d grab them in...
Do you do this often dusteater? I’d grab them in a flash if bitslong hadn’t beaten me to it.
Sent from my iPhone using Tapatalk