Search:
Type: Posts; User: Don Davis
Search: Search took 0.01 seconds.
-
22nd December 2018, 10:42 AM
Thread: Help with Vicmarc VL-240
by Don Davis- Replies
- 8
- Views
- 1,852
Neil and plt43, my stop bar was stuck! I think a...
Neil and plt43, my stop bar was stuck! I think a shaving was stuck in there, I blew it out real good with my air compressor and oila it started running again--thanks for pointing me in a right...
-
22nd December 2018, 03:05 AM
Thread: Help with Vicmarc VL-240
by Don Davis- Replies
- 8
- Views
- 1,852
Help with Vicmarc VL-240
I purchased a Vicmarc VL-240 several months ago, and have been liking it so far. Yesterday I went down to my shop to do a NE bowl, and turned the power on to my lathe and it will not start--when I...
-
19th September 2018, 06:02 AM
Thread: Experience with Vicmarc 240 lathe
by Don Davis- Replies
- 17
- Views
- 22,007
Hey Colin, thanks for the post--I had narrowed my...
Hey Colin, thanks for the post--I had narrowed my choices down to a Robust-an American Beauty, a Oneway and the Vicmarc-it may sound silly but I felt like a digital speed readout was an essential...
-
18th September 2018, 01:41 PM
Thread: Experience with Vicmarc 240 lathe
by Don Davis- Replies
- 17
- Views
- 22,007
Treecycle, this is a brand new lathe and it is...
Treecycle, this is a brand new lathe and it is made for the USA market by Vicmarc and therefore it is set up to run on our higher voltage residential circuits at 220 volts, so in short it is...
-
18th September 2018, 09:57 AM
Thread: Experience with Vicmarc 240 lathe
by Don Davis- Replies
- 17
- Views
- 22,007
I appreciate the input folks, I am still not sure...
I appreciate the input folks, I am still not sure if I should mess with my VFD, I'm not going to at this point. My distributor I purchased the lathe from has been very supportive, and I hoping he...
-
17th September 2018, 10:26 AM
Thread: Experience with Vicmarc 240 lathe
by Don Davis- Replies
- 17
- Views
- 22,007
Thanks for the feedback Simon and Optimark, I too...
Thanks for the feedback Simon and Optimark, I too a thinking there is an issues with my particular lathe--Marco--a principal at Vicmarc--was not helpful when my distributor I bought the lathe from...
-
14th September 2018, 09:55 AM
Thread: Experience with Vicmarc 240 lathe
by Don Davis- Replies
- 17
- Views
- 22,007
Thanks for the feedback folks, Acco, I didn't see...
Thanks for the feedback folks, Acco, I didn't see anything about adjusting the VFD on my lathe in the manual, but I have not adjusted it due to that--I would be very interested to know what...
-
13th September 2018, 05:32 AM
Thread: Experience with Vicmarc 240 lathe
by Don Davis- Replies
- 17
- Views
- 22,007
Thanks for the reply Paul, I do in fact have my...
Thanks for the reply Paul, I do in fact have my pulley set at the 1-3 ratio, and the wood I am working with is green spalted maple. So this doesn't seem to lead anywhere as to a reason for what I am...
-
13th September 2018, 02:19 AM
Thread: Experience with Vicmarc 240 lathe
by Don Davis- Replies
- 17
- Views
- 22,007
Experience with Vicmarc 240 lathe
I recently purchased a Vicmarc 240 ASM heavy duty lathe. I went with the Vic largely due to the recommendation of my contact at the US distributor of Vicmarc lathes--Woodworkers Emporium. I like many...