Search:

Type: Posts; User: cjbfisher

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    673

    Thanks for the replies and suggestions. I managed...

    Thanks for the replies and suggestions. I managed to get everything pretty close.
    I started with just putting them out in the sun, but it wasn't really happening for me, so I ended up laying them on...
  2. Replies
    5
    Views
    673

    Thanks Elan, Some of them had started to flatten...

    Thanks Elan,
    Some of them had started to flatten out a bit by the end of the day yesterday, but not as much as I had hoped. I think I'll have a go at putting them in the sun, as I feel that I've got...
  3. Replies
    5
    Views
    673

    Help/advice needed - cupped panels

    I need some helpful advice on how to tackle a problem.
    I am building some shelving out of Blackbutt to fit under the overhead cupboards in a kitchen.
    I've glued up all the panels, which are 340mm...
  4. I would use Everdure/epoxy to seal it, but I can...

    I would use Everdure/epoxy to seal it, but I can see that you don't want to go to that extreme. I think it would make a stunning planter, and I would make the effort to seal it properly.
  5. Replies
    5
    Views
    729

    N.S.W. If, for any reason, Pat doesn't take them, I will.

    If, for any reason, Pat doesn't take them, I will.
  6. Fuzzie, Now that you've got the socket adapter,...

    Fuzzie,
    Now that you've got the socket adapter, forget about replacing the broken bit. Use the socket adapter and appropriately sized socket in a drill, and you've got an electric start brushcutter....
  7. Looking at those last two pics, you can see a...

    Looking at those last two pics, you can see a little "hook" that fits into the back on the drawer, so once the drawer is released from its fixing it will need to slide forward to remove it.
    On your...
  8. Replies
    0
    Views
    505

    Chisel Morticer set up/parts

    I have a small chisel morticer that I got from a deceased estate some years ago, and I'm finally getting around to setting it up.

    476731

    As you can see, it has been bastardized to a degree by...
  9. Replies
    2
    Views
    1,335

    I finally got around to doing something with...

    I finally got around to doing something with this.
    I did away with the plastic cover, replacing it with a ply one, and used a 150mm Y and some re-shaped pieces of 150mm pipe to widen to pick up...
  10. Replies
    11
    Views
    1,101

    They were the $125 option. Needless to say that...

    They were the $125 option. Needless to say that they didn't get the order.
  11. Replies
    11
    Views
    1,101

    Update: I got prices from 2 online stores and...

    Update:
    I got prices from 2 online stores and one from my local Trade Tools store.
    Online store 1: $125.00 incl shipping
    Online store 2 : $88.00 incl shipping
    Trade Tools: $73.00 but need to pick...
  12. Replies
    11
    Views
    1,101

    Where to buy Makita spare parts?

    Does anyone have any recommendations for where to get good service and prices for Makita spare parts?
    I need to replace the front roller assembly and the plastic separator in the blower on my 9403...
  13. Replies
    15
    Views
    1,039

    I have done this on both my rails. They come in 3...

    I have done this on both my rails. They come in 3 metre rolls. I got mine from Trade Tools for $14.50 per roll.
  14. Replies
    7
    Views
    1,038

    Probably depends on which way the wind is...

    Probably depends on which way the wind is blowing.
    Sorry, I couldn't help myself.
    I'll show myself out.
  15. Replies
    8
    Views
    950

    Is he kinked, or is he kinky?

    Is he kinked, or is he kinky?
  16. Replies
    8
    Views
    491

    Welcome, neighbour.

    Welcome, neighbour.
  17. I just wrap them in packing tape.

    I just wrap them in packing tape.
  18. I have both a 1013 and a 1016, and I can tell you...

    I have both a 1013 and a 1016, and I can tell you from personal experience that the two saws are worlds apart. I think the 1016 is an overpriced piece of junk. The 1013, on the other hand is a great...
  19. Lance, Would you mind sharing where you bought...

    Lance,
    Would you mind sharing where you bought the igaging bevel from?
  20. Replies
    23
    Views
    1,767

    Makita 9403. I've used one of these very heavily...

    Makita 9403. I've used one of these very heavily for probably close to 7 years (in an industrial setting). The only things I've had to do to it in that time is replace the graphite slip pad and I...
  21. Replies
    13
    Views
    1,263

    Beautiful! I have no other words.

    Beautiful!
    I have no other words.
  22. Gone to a new home, and not to the tip.

    Gone to a new home, and not to the tip.
  23. FREE: QLD Gone.

    Gone.
  24. Replies
    9
    Views
    1,088

    Being that your carts are going to be mobile,...

    Being that your carts are going to be mobile, this may not necessarily apply, but as most of us are hobbyists we quite often struggle to make do with what space we have. When I am setting things up,...
  25. Replies
    9
    Views
    1,088

    You're either very short, or you should consider...

    You're either very short, or you should consider a more supportive brassiere.
  26. Thread: Euro Screws

    by cjbfisher
    Replies
    9
    Views
    1,570

    You could try Lincoln Sentry. They have a branch...

    You could try Lincoln Sentry. They have a branch in Newcastle. Not sure if they are trade only, though.
  27. FREE: QLD JEM Watercraft Sabalo 15 plywood kayak. Needs finishing.

    Link to post in Wooden Boat section:

    https://www.woodworkforums.com/f269/free-jem-watercraft-sabalo-15-finishing-232060#post2167923
  28. FREE - JEM Watercraft Sabalo 15. Needs finishing.

    This is something that I started a looooong time ago, and it's been sitting around untouched for the last 5 years or so.
    I think it's time for it to find a new home.

    The hull has been assembled...
  29. Replies
    2
    Views
    1,057

    QUEENSLAND Make me an offer.

    Make me an offer.
  30. Replies
    2
    Views
    1,057

    QUEENSLAND Any interest at $100 before it goes on...

    Any interest at $100 before it goes on Gumtree/Marketplace?
  31. Replies
    2
    Views
    1,057

    QUEENSLAND Soft Close Drawer Runners

    I removed these from a kitchen, as the German owner wanted to change everything over to Blum. He then went ahead and dismantled them to retrieve the white board bottoms and backs while I was gone...
  32. Replies
    22
    Views
    1,553

    Looks good. I would like to make a suggestion,...

    Looks good.
    I would like to make a suggestion, if I may. I find the photos in the gallery a bit small. Would it be possible to click on them to open a full size photo?
    P.S. I was going to ask who...
  33. Replies
    22
    Views
    1,553

    That's fantastic, and I wish you all the best. I...

    That's fantastic, and I wish you all the best. I wish I was in a situation where I could do the same.
  34. Replies
    12
    Views
    2,374

    Sorry for the lack of replies, as I've been away....

    Sorry for the lack of replies, as I've been away.



    Not quite. The 5 metre Festool strip is $71 from Carbatec. I can get 2 x 3 metre Makita strips for $14.50 each from Trade Tools. Still waiting...
  35. Replies
    12
    Views
    2,374

    Thanks for the replies. I've done the ring...

    Thanks for the replies. I've done the ring around, inquiring about the Makita strips, and no-one stocks it but will get back to me on Monday. A fella at work has a couple of Makita tracks that appear...
  36. Replies
    12
    Views
    2,374

    Alternative for plastic strip on tracks

    I have had a quick search of the forum, but couldn't find an answer. That doesn't mean it's not there, but probably more so that my search capability sucks.
    I'm looking for an alternative to the...
  37. Replies
    5
    Views
    1,370

    What species are you looking for and in what...

    What species are you looking for and in what quantities?
    Most of the places I know are wholesalers.
    Bootle Timbers at Loganholme would be the first one that I'd try. These guys will probably deal...
  38. Replies
    5
    Views
    1,002

    WANTED:QLD. I haven't bought any for a very long time, and am...

    I haven't bought any for a very long time, and am surprised at the price. I was expecting it to be around $3650/m3.:2tsup:
  39. Replies
    4
    Views
    1,148

    This really should be in the market place...

    This really should be in the market place section, and will need to have a price.
  40. Replies
    5
    Views
    1,002

    WANTED:QLD. Try Bootle Timbers in Loganholme. 3209 8688.

    Try Bootle Timbers in Loganholme.
    3209 8688.
  41. Replies
    6
    Views
    1,328

    That's very cool. Thanks for sharing your story.

    That's very cool. Thanks for sharing your story.
  42. Replies
    8
    Views
    1,091

    Is there anything else other than the glue...

    Is there anything else other than the glue holding the joint together?
    I think that they will look quite unattractive if you put them back in, but if you're going to have a hole to fill, why not put...
  43. Replies
    2
    Views
    2,498

    Release agent for bending form?

    Hi guys,
    I have to glue up some curved beams for the roof of a boat that my boss is having restored. There will be 5 in total. They will be 2800mm in length with 100mm of curvature.
    I am going to...
  44. Replies
    7
    Views
    1,673

    Thanks for your replies. Tony, I'm not sure of...

    Thanks for your replies.
    Tony, I'm not sure of your reasoning for suggesting the DC go on the SW corner. In my head, it only seems to make the run of ducting longer. As far as floor vacs go,...
  45. Replies
    7
    Views
    1,673

    Thanks Bob. I had considered that the jointer was...

    Thanks Bob. I had considered that the jointer was closer to the dusty in that configuration, and was just wanting someone to back up my thoughts. As far as the windows go, I will have to keep them...
  46. Replies
    7
    Views
    1,673

    Ok, so here's what I had in mind. I was going to...

    Ok, so here's what I had in mind. I was going to hold off posting these as I wanted to see some other opinions in case I influenced someone else's ideas.

    The first is with the dusty in my...
  47. Replies
    7
    Views
    1,673

    Ducting path/location

    I'm hoping to get some ideas/advice from the collective brains trust. I'm at the point where I need to start running my duct work, and I'm not sure what the best configuration would be. I'll start...
  48. Hi James, I can't give any Melbourne based...

    Hi James,
    I can't give any Melbourne based advice, but when I built my shed I used one of the Ranbuild suppliers as they were the only company that would listen to what I wanted. My council would...
  49. Thread: Surprise!

    by cjbfisher
    Replies
    258
    Views
    77,505

    Fletty, That looks fantastic. Well done. I'm...

    Fletty,
    That looks fantastic. Well done. I'm looking forward to seeing it finished.
  50. Replies
    1
    Views
    1,379

    QUEENSLAND Make an offer. If it's still here by the end of...

    Make an offer. If it's still here by the end of next weekend, it will go to the dump.
Results 1 to 50 of 301
Page 1 of 7 1 2 3 4