Search:

Dont know about the particular green shed stuff but quality steel edging will be made out of Corten Steel
Weathering steel - Wikipedia

Yours appears to be a close copy of a Record No.52
It uses the spiral spring but no sign of the castellated device.

536036536037


A spacer should work fine, with that spring there is no way...

Never tried it for that purpose but have glazed plenty of windows with linseed putty.
Just wondering what problem or issue you are looking to solve?

Initial thoughts are bog sets hard whereas...

Flow should be through the case, usual is in at the front and out at the back.
Unless you are building an extreme unit with multiple CPU's, graphics cards and large amounts of ram a single fan front...

Make sure any stops at the top have been wound down, door should lift up and inwards.

The thing that will stop it is it looks like the bottom track is bowed up in the middle ? If this is the case...

Have a read of the rules for the market place
RULES for posting in Market Place

Yes a bandsaw can be used to make veneer.
https://timothycoleman.com/wp-content/uploads/2017/06/Bandsaw-Your-Own-Veneer.pdf


I have never done it personally but it will require well setup...

Have you looked at the seals that have a stop on the door jamb that push them down into the closed position, and lift as the door opens?
RP3 Automatic Weather Seal 920mm Anodised (Silver)

Maybe try a cheaper version and see if there is significant improvement first ?...

It may be possible to replace the LED’s but first of all you need to identify the device itself rather than the plastic lens in front of it.
Next question is do you have the tools or experience to...

My goto paint is Dulux, have tried many other brands but have not been impressed. Others have their favourite but with paint it appears YMMV.

99% of all my windows are double hung sash and unless...

Frames look in good condition compared to some I have repaired in the past.
Sand and clean the glass rebates of any old putty or sealant.
Prime and topcoat all over including the rebate with...

Is it the same stuff as car windows ?
It is called Bailey channel available at auto restoration supply or Clark Rubber.
Bailey Channel Rubber | Clark Rubber

Or is it just the furry strip ?...

Without first hand examination it’s impossible to say, but may be possible depending on construction.

Sorry to say but it looks like it has gone too far and complete replacement of the bottom sill is the only option in my opinion.

Ah so already repaired looking for option for prevention of future occurrence.

Even switching the equipment off at the outlet is often only disconnecting the active, unless you have specific...

From a quick google it appears the lathe is powered by a Striatech digital variable reluctance motor and looks to use a solid state controller.
One common issue with solid state controllers is...

Something about the rating does not sound right to me given that it is on a 240v motor.

Not sure where in Brisbane your located but have you tried a Jaycar store ?

Post 3 ??

And from Feast Watsons website

The motor is 240v Alternating Current !
There is no positive or negative as it alternates between the two.

Based on the age I would expect that it would have been a spirit based stain then clear over the top.

A number of manufacturers still do spirit based stains, any good outlet should have a display...

Is the product you using a stain? Or a stain / varnish?

And is the product water or oil based ?

Use a spirit based stain to get the colour you want, then overcoat with a clear finish of your...

Agree to have the manufacturer measure, any mistake is then on them to rectify.

Generic installation diagrams can be found here
Attention Required! | Cloudflare

Back on the Renovate Forum all the builders used to recommend the Franklin Sensors brand.
Professional Stud Finders | Stud Sensor | Stud Detector

I bought this one PROSENSOR 710 - Franklin...

Flooring species is often tied to state and age of construction.
Not being from NSW and unknown date my best guess by look I would suggest maybe Tallowwood

A lot depends on panel thickness and the desired result. I remember a lot of early caravans had a laminex table that used to fold down as the bed, the top was edged with an aluminium strip screwed in...

:whs:

Mass damper

HOLDEN VY VZ 1-TONNER REAR LEAF SPRING MASS DAMPER # 92168169 | eBay

Most likely the start capacitor is failing.
It is usually a round canister on the side of the motor.
If you are not experienced around electrical get an electrician to assist.

Just do a google search on "CNC Cabinet Door Manufacturer Victoria" and start a call around.

Probably better to start a search in your local area rather than Victoria which is a pretty wide area....

4mm diameter ?
Try pulling apart a few ball point pens they are about that diameter, just trim to required length with a pair of side cutters.

E-clip
E Type Clip - United Fasteners

Because they are short bolts into limited amount of block material, they are also smaller thread size.

Except when different torque specs are specified for some of the bolts!
https://arpinstructions.com/instructions/134-3610.pdf

Sandpaper should cut freely, it will only burn if it is clogged. I would start at 180 maybe 120 but the coating will tell you what it needs. Have to be careful as it is a veneer finish.
The current...

The term for the problem is snipe.
Do a search on thicknesser snipe, It can be due to setup and or procedure and can be hard to eliminate all of it.
Starting with longer lengths and cutting to size...

The 6mm thick veneer is most likely 6mm plywood, the top level veneer is probably 1mm or less.
Exterior you do not use clear due to the UV, a tint is added for protection.
The coating has lifted or...

Maybe not yet notified, just like I have only received notification on 2 of my 6 email addresses with iiNet.
NodeSupport / Faq / Internode Email Messaging Company | Internode

Same is happening for iiNet users but the instructions so far have provided details to have the email address migrated to "The Messaging Company" for continued hosting of that address.

You can...

There is a good reason that skirtings are scribed for internal corners.
You will find it much easier for your next room.

Duct tape should stretch, make sure you leave the roll in the sun or warm location prior to use.
When applying you need to provide enough force to stretch the tape so it takes up the difference in...

Having never used Osmo I cannot make recommendations for overcoating.

My preference for timber benchtops is one of the two pack coatings, in the past I have used Wattyl 7008 with great success.
I...

Exactly the reason that those members on the RenovateForum used it on bathroom vanity benchtops, did not stop the fact they ended up with water marks and calls to the manufacturer for support did not...

Never used the product myself but there was a lot of discussion on the (now closed) RenovateForum.

There were a number of members that had the exact same issue of water stains with the Osmo...

Parts diagram indicates screw on.
Black & Decker BD142 Type 1 Hammer Drill Spare Parts - Part Shop Direct


3/8 x 24 unf
Black & Decker X66301 Male Chuck & Key 13Mm Use Sta66301 - X66301 | Tools...

Maybe follow the manufacturers recommendation ?
Why is the surface still sticky after application? - Osmo UK

Maybe if you provide details of your current cutting operation (handsaw, circular saw, bandsaw, SCMS, etc) including blade type, as well as the tools that you have available then someone will be able...

I believe it simply a styling design and provides more glass area than other panel door designs.

I fail to understand why you are mixing the Exterior clear and acrylic paint ? :?

Now understanding the intended use, have you researched what any coating absorbed into the timber will do to the taste from a termites perspective?

Termites can be very selective, eat one piece of...