Search:

Type: Posts; User: lyleman

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,959

    Hi Ken, I have a late one of these and I love...

    Hi Ken,
    I have a late one of these and I love it.
    I have the standard 3 phase motor, no VFD, Speed range is great for what i do. I have not done much horizontal milling other than brass but for...
  2. Replies
    16
    Views
    8,124

    Just realized that I made a small error in he...

    Just realized that I made a small error in he vertical head speed calc http://d1r5wj36adg1sk.cloudfront.net/images/smilies/actions/doh.gif, I forgot to factor in the primary drive gear ratio from the...
  3. Replies
    16
    Views
    8,124

    Hi Nev, Mine is 1/2 horse I think. My motor has...

    Hi Nev,
    Mine is 1/2 horse I think. My motor has a two step toothed belt pulley on the end of it. The motor itself has no internal gear reduction / stepup if thats what you mean. If I need more...
  4. Replies
    16
    Views
    8,124

    I looked at my vertical head that I have apart to...

    I looked at my vertical head that I have apart to clean the grease out of it, the gear ratio is 1.03:1. There is not much overdrive there.
    I had read that it was much higher than that.
    Lyle.
  5. Replies
    16
    Views
    8,124

    Here is a really bad pic off my phone. I will...

    Here is a really bad pic off my phone. I will take a good one when I can.
  6. Replies
    16
    Views
    8,124

    Hi Bill, I will take a photo of the spindle speed...

    Hi Bill, I will take a photo of the spindle speed plate on my mill when I am near it next, It may be a couple of days though.
    Lyle.
  7. Replies
    2
    Views
    4,025

    If It was closer to home I may have found the...

    If It was closer to home I may have found the room.....
  8. Replies
    16
    Views
    8,124

    Hi Nev, Yes mine is the 3 slot table metric...

    Hi Nev,
    Yes mine is the 3 slot table metric unit.
    Mine is serial # OLM 578 so it is a fairly late one. It has the 16 speed gearbox ( I Think) It has the two step pulley on the motor.
    Lyle
  9. Replies
    2
    Views
    4,025

    Invicta shaper on e bay

    http://www.ebay.com.au/itm/Metal-Shaper-Mill-/231496126435?pt=LH_DefaultDomain_15&hash=item35e63e8fe3Invicta shaper,I wish I had a bigger shed...
  10. Replies
    16
    Views
    8,124

    Thanks Mate.

    Thanks Mate.
  11. Replies
    16
    Views
    8,124

    Hi Nev, Does that manual cover the later OLM...

    Hi Nev, Does that manual cover the later OLM machine?, or is there not much difference between the two.
    Lyle.
  12. Replies
    0
    Views
    4,572

    Hercus Mill on evilbay

    Hi Guys, If anyone is interested there is a Hercus Model O mill on e-bay cheap. (In Sydney)
    Lyle.
    ...
  13. Replies
    2
    Views
    1,082

    Yes mate, I sure did. I have been after a mill...

    Yes mate, I sure did. I have been after a mill for ages, patience and go luck paid off. It appears to be in great condition.
  14. Replies
    2
    Views
    1,082

    Hercus OLM Mill

    Hi Guys, New to the forum as far as posting goes.
    I have purchased a Hercus OLM Mill, the 3 slot version. I was wondering if anyone might have a user manual for one of these?
    I have owned few...
  15. Thread: Hercus Model 0

    by lyleman
    Replies
    15
    Views
    2,345

    Hercus mill

    Hi Guys, this is my first post ,I hope it is in the right spot.
    I have recently picked up a Hercus OLM mill and was wondering if anyone here might have a copy of the original user manual.
    Mine is...
Results 1 to 15 of 15