Search:
Type: Posts; User: Bemboka
Search: Search took 0.00 seconds.
-
5th May 2008, 02:39 PM
Thread: Looking for Garrett Wade 202GF glue
by Bemboka- Replies
- 4
- Views
- 3,749
Looking for Garrett Wade 202GF glue
Does anyone know of a supplier of 202GF in Australia? Anton Gerner no longer carries it.
-
6th February 2007, 05:07 PM
Thread: Aluminium windows
by Bemboka- Replies
- 6
- Views
- 4,693
I've been making timber casement windows and door...
I've been making timber casement windows and door frames for the house we're building. But havn't had any experience with aluminium. Not sure really where to start. I've talked to aluminium...
-
6th February 2007, 01:34 PM
Thread: Aluminium windows
by Bemboka- Replies
- 6
- Views
- 4,693
Aluminium windows
Has anyone had any experience with making their own aluminium windows ?
-
23rd November 2006, 01:02 PM
Thread: Glass standards
by Bemboka- Replies
- 3
- Views
- 1,379
Glass standards
Is anyone familiar with the NSW standards re thickness/type of glass you can use in windows and doors ?
-
6th November 2006, 09:07 AM
Thread: Correct way to glaze windows
by Bemboka- Replies
- 18
- Views
- 9,982
Correct way to glaze windows
Is there a reason most windows seem to have the glass fitted from the outside rather than the inside of the room ?
-
14th September 2006, 06:57 PM
Thread: Making casement windows
by Bemboka- Replies
- 7
- Views
- 12,612
Thanks
Yeh, I plan to make the windows because they are specific sizes in order to avoid cutting bricks into thirds (and worse) and I like the idea of making them a little different to the mass produced...
-
7th September 2006, 01:18 PM
Thread: Making casement windows
by Bemboka- Replies
- 7
- Views
- 12,612
Making casement windows
Looking for some plans for, or thoughts based on first hand experience from, making timber casement windows. In particular types of timber and hardware used.
I have about 10 to make for my house... -
23rd January 2006, 03:57 PM
Thread: Bearers and joists
by Bemboka- Replies
- 20
- Views
- 4,929
Hope it doesn't get too trendy. We're moving...
Hope it doesn't get too trendy. We're moving there to get away from that sort of junk. Can you recommend any good concretors around that area ?
-
23rd January 2006, 03:53 PM
Thread: Bearers and joists
by Bemboka- Replies
- 20
- Views
- 4,929
Timbercrete
Not sure about Candelo - the supplier I spoke with is from Nowra. I've spoken to a few people and checked out some structures made from it. It seems to be as good as it reads.
-
23rd January 2006, 02:19 PM
Thread: Bearers and joists
by Bemboka- Replies
- 20
- Views
- 4,929
Good point - that's where discussions like this...
Good point - that's where discussions like this are a good opportunity to learn. I suppose I could go 9,000 x 8,000 instead of 10,000 x 8,000 if that simplified things. The later was somewhat of an...
-
23rd January 2006, 01:16 PM
Thread: Bearers and joists
by Bemboka- Replies
- 20
- Views
- 4,929
The concept is to have the lower area as large as...
The concept is to have the lower area as large as possible. We can run a wall across at 3000 - making two spans of 5000 and 3000. But the ideal was to make all internal walls non-load bearing so we...
-
23rd January 2006, 12:26 PM
Thread: Bearers and joists
by Bemboka- Replies
- 20
- Views
- 4,929
Thanks Peter. Sorry I didn't get the jargon all...
Thanks Peter. Sorry I didn't get the jargon all correct. Thought the idea was to be able to ask for help here. I have read a bit about Hyspan - for rough budgeting purposes what should I allow for...
-
22nd January 2006, 04:00 PM
Thread: Bearers and joists
by Bemboka- Replies
- 20
- Views
- 4,929
Bearers and joists
I'm designing a (small) house for my block at Bemboka. Two storey, 8,000mm x 10,000mm out of timbercrete. I'd appreciate some input on bearers and joists for the the second level tongue and groove...