Search:
Type: Posts; User: romerod
Search: Search took 0.00 seconds.
-
7th August 2015, 01:57 PM
Thread: Waldown 3M vs 8SN
by romerod- Replies
- 2
- Views
- 931
Waldown 3M vs 8SN
Hi All,
I have a Waldown 8SN in good condition. I purchased it some years back from a bloke in Gippsland and unfortunately it has rusted up a bit as it was sitting exposed in the corner of his... -
16th July 2015, 02:34 PM
- Replies
- 7
- Views
- 3,875
Transtig 275 operating manual
Better late than never. Hope this helps
Cheers -
15th July 2015, 03:28 PM
Thread: Which drill press to keep?
by romerod- Replies
- 13
- Views
- 3,060
Keep the Waldown!!!
HI I would keep the old Waldown as it is a much more desirable and versatile machine.
-
22nd April 2015, 09:02 PM
Thread: Early Waldown Restoration
by romerod- Replies
- 80
- Views
- 9,425
waldown 8SN table rack
Hi all
High jacking the thread a bit I was wondering if anyone has experience with the Waldown 8sn table lift mechanism. When I purchased my unit the table lift was not operational. The rack rod... -
11th April 2015, 09:27 PM
- Replies
- 7
- Views
- 3,875
I have a copy of this manual around somewhere if...
I have a copy of this manual around somewhere if you still want it for other information.
Cheers -
11th April 2015, 09:25 PM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Little too late for me :-(
Hi Sibrand,
I was just searching the forums and came across my old thread on the Transtig 150. Seems like such a simple fix, I wish I still had it now as it was a well sized machine for what I... -
8th September 2013, 08:57 PM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Thanks for the help. She's sold
:(( Hi guys thanks for all of the replies and help. I had no luck with all of my fault finding so I bit the bullet and sold it. Hopefully the next guy will have more luck than I did.
thanks again... -
25th August 2013, 08:55 PM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Still no big spark
:?:?
Hi guys, been a bit busy with work and haven't been playing with the old Tig for the moment. Thanks to the replies so far. On the plus side I managed to repair my Fluke! It has a sneaky fusible... -
28th July 2013, 11:18 AM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Further update maybe its all over
:cry4: I changed out the melted looking wire from the SCR to the change over panel on the front, got a new Dinse plug for BOC as well, point to note is that BOC supplied plugs are shorter than the...
-
22nd July 2013, 09:35 PM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Thanks for the heads up on that. I actually...
Thanks for the heads up on that. I actually noticed that one of the plugs looks like it has arced and even melted the insulation a bit. Might see if I can get a new cable for it maybe?
-
22nd July 2013, 09:04 PM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Light bulb!
Thanks for the reply. That makes so much sense! Just need to know how to test and check transformers. Any clues?
there may be hope for the old girl yet.
will keep you posted.
cheers -
21st July 2013, 10:29 PM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Help? The update
So all, thanks for all the replies and posting of manuals.
i finally got hold of an air cooled tig torch and hooked up the Transtig 150. What if found was that the per and post flow timers and gas... -
16th July 2013, 10:23 PM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Thanks
Thanks!! Need to get a hold of a Tig torch that fits to try it out.
Will let you know -
9th July 2013, 10:02 PM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Thanks!
Thanks!
PM replied to, will see what the manual says.
Cheers -
6th July 2013, 10:49 PM
Thread: CIG Transtig 150
by romerod- Replies
- 27
- Views
- 14,494
Help my Transtig 150 is not working
Hi I am having a horror run with Transtig welders at the moment. I recently purchased a EMF 250 Transtig which is in great condition but its too big for me and won't fit in my workshop. Apparently...
-
4th June 2013, 03:17 PM
Thread: Looking for manual for CIG Transtig 250
by romerod- Replies
- 5
- Views
- 2,529
EMF Transtig 250
Hi there,
I have PM'd you my address.
Cheers -
3rd June 2013, 09:28 PM
Thread: Looking for manual for CIG Transtig 250
by romerod- Replies
- 5
- Views
- 2,529
Can I have a copy?
Hi mate
Any chance I could get a copy of that manual?
I have one of these old machines as well and want to learn a bit more about it.
cheers