Search:
Type: Posts; User: gyro
Search: Search took 0.00 seconds; generated 13 minute(s) ago.
-
23rd April 2008, 11:53 PM
Thread: Moving a split-system aircon.
by gyro- Replies
- 11
- Views
- 2,468
moving a split system
Need a frig tech, he will pump the refrigerant back into the outdoor unit and seal off the valves on the outdoor unit. Then dicsconnect the indoor unit and wiring as he would have an electrical...
-
26th March 2008, 09:17 AM
Thread: Need advice on dishwashers..
by gyro- Replies
- 32
- Views
- 8,843
The SB980WK is the new unit made in Italy, looks...
The SB980WK is the new unit made in Italy, looks to be a good unit. there is a recall on re the main control printed cct board.(if the unit is between xx and xx serial nos. check the electrolux webb...
-
17th March 2008, 11:15 PM
Thread: split system fan not working
by gyro- Replies
- 5
- Views
- 2,454
the motors are transistor driven from the indoor...
the motors are transistor driven from the indoor pcb, not available and you cant substitute tthe motor. Nor can you mix and match indoor and outdoor units. cheapest option is to go to local hardware...
-
17th March 2008, 10:41 PM
Thread: Capacitor replacement in bench grinder.
by gyro- Replies
- 9
- Views
- 14,319
dont do it
Hi, the capacitor is there for a phase shift between the 2 windings in the motor. you can easily get a capacitor at any appliance repair place that is the same as the original. going too far from the...
-
18th June 2007, 08:52 PM
- Replies
- 26
- Views
- 2,741
Drilling Holes
I cut my blanks in half and mark then with a texta so i can always get the grain matched. Then only drill a half the pen at a time. The blanks are clamped in a jig to ensure no movement. Works a...
-
13th June 2007, 11:31 PM
Thread: Huon pine tear out.
by gyro- Replies
- 9
- Views
- 1,097
Thanks Members
I have a lot to check for with all your ideas. Will review my methods and check with the magnification, might give me some answers.
No I don't normally have any problems with other wood, but that... -
12th June 2007, 10:48 PM
Thread: New Superjaws Review
by gyro- Replies
- 15
- Views
- 4,252
My new Superjaws.
It's standing by the front door "in the lounge room" nick named the Great Dane, my wife even stuck a tail on it.:roll:
-
12th June 2007, 10:03 PM
Thread: Huon pine tear out.
by gyro- Replies
- 9
- Views
- 1,097
Huon pine tear out.
Hi, when I get near the thinest part near the bush I get tearing out of small lumps. I have tried different lathe speeds and very soft cuts but no success. I know this is a very soft timber but the...
-
24th April 2007, 11:24 PM
Thread: Triton dust respirator
by gyro- Replies
- 8
- Views
- 1,877
[QUOTE=jimj;496136]Sorry for the dumb question...
[QUOTE=jimj;496136]Sorry for the dumb question and this may have already
You can get a kit for removig scratches of of CD's this works well as it is a two part application, I think the first part... -
27th February 2007, 10:28 AM
Thread: Power respirator won't work.
by gyro- Replies
- 4
- Views
- 1,538
Power respirator won't work.
Removed 4 screws from bottom, seperated top and bottom.found 1 small fan motor and 2 batteries. Problem was where wire was soldered on to the terminal of the fan motor, wire had broken off, (wire is...
-
10th February 2007, 01:51 PM
Thread: Dual Trade
by gyro- Replies
- 64
- Views
- 9,719
I have 2 adult refrig lads going thru trade...
I have 2 adult refrig lads going thru trade school at the moment, they have log books and need them signed off, some of the work they are required to do we dont do so they are sent off to another...
-
19th June 2006, 11:59 PM
Thread: Bevel less than 15 degrees
by gyro- Replies
- 24
- Views
- 3,195
DPB where did you get the "hand crafted by Don...
DPB where did you get the "hand crafted by Don Barton " emblems.
I have serched high and low to find out where?
Gyro -
12th June 2006, 04:35 PM
Thread: Weatherwall ac/Heater...
by gyro- Replies
- 1
- Views
- 3,418
weatherwall help.
Hi, looks like no one wanted to reply so will try to help as i have had considerable experience with these. (ISOLATE THE UNIT) turn off the power at the meter box and check the unit wont work,, 1st...
-
21st February 2006, 07:19 PM
Thread: French Door Locks
by gyro- Replies
- 12
- Views
- 13,926
If the doors are external then check your...
If the doors are external then check your insurance policy, mine had to be deadlocks. Which was not easy as the doors were too thin so new doors for me unfortunately.
-
21st February 2006, 06:49 PM
Thread: Left of Centre Grey Water Solution
by gyro- Replies
- 23
- Views
- 3,645
A friend of mine did this and all their plants...
A friend of mine did this and all their plants had stunted growth, they eventually gave up on it and now they have had to remove the soil and get in fresh soil and plants.
-
17th January 2006, 11:38 PM
Thread: Speed Control
by gyro- Replies
- 14
- Views
- 3,029
They work
Hi,
I have made two of the Dick Smith/Silicon chip speed controls, I use one for a large buff for polishing the car which had a speed control but lasted a day so i bypassed it and now use the one i... -
12th October 2005, 09:55 PM
Thread: triton power hat
by gyro- Replies
- 5
- Views
- 1,853
gyro
thanks for that, I will now paint it orange and try to find the instruction book.
-
12th October 2005, 07:33 PM
Thread: triton power hat
by gyro- Replies
- 5
- Views
- 1,853
triton power hat
If anyone has a powered hat could they tell me the voltage on the 240v charger. I have so many im not sure which one to use. I must tag it.
thanks.
gyro -
29th June 2005, 12:27 AM
Thread: DeWalts attract bees
by gyro- Replies
- 5
- Views
- 1,845
I had a van with a yellow stripe around it and...
I had a van with a yellow stripe around it and never again, some days you could not get near it for the bee's
-
15th June 2005, 09:54 PM
Thread: pens for kids
by gyro- Replies
- 1
- Views
- 1,006
Pig pens
So is your shed clean?
pigs could live in mine! :) -
15th June 2005, 09:46 PM
Thread: Wooden spoked wheels
by gyro- Replies
- 9
- Views
- 5,140
Wooden wheels
Thanks guys n galls,
Found a book "Building Antique Model Cars in wood"
isbn 1-895569-51-6 Local library had it and have ordered one for myself.
check it out if you are interested in old model... -
22nd May 2005, 03:28 PM
Thread: Wooden spoked wheels
by gyro- Replies
- 9
- Views
- 5,140
Thank you, looks interesting
Thank you, looks interesting
-
21st May 2005, 12:55 AM
Thread: Wooden spoked wheels
by gyro- Replies
- 9
- Views
- 5,140
Wooden spoked wheels
Any ideas on where I can get info on building model wooden spoked wheels.
I once saw an article on it and cant remember where i saw it.