Search:
Type: Posts; User: parkinson
Search: Search took 0.00 seconds.
-
21st April 2012, 01:26 PM
- Replies
- 12
- Views
- 4,268
Iv owned both Makita14v NiCad AEG18v NiCad and...
Iv owned both Makita14v NiCad AEG18v NiCad and AEG18v lithium-ion and now I use a Bosch blue 36v lithium-ion and it kick ass!
Lithium-ion is by far the best if u can justify spending the extra... -
15th February 2012, 06:48 PM
Thread: Shed Wiring
by parkinson- Replies
- 13
- Views
- 3,182
U really dont need any j/boxes in a shed just...
U really dont need any j/boxes in a shed just loop in and out of each power point, if u r going to run the cable in your c section at 1200mm with the opening to the front u need to really to put it...
-
15th February 2012, 05:25 PM
Thread: What size box section should I use?
by parkinson- Replies
- 13
- Views
- 2,014
I think that 50mm box by 3mm, Plus that brace....
I think that 50mm box by 3mm, Plus that brace. Would hold any human. But I think what u have drawn there would be ideal. That looks good.
Scott -
15th February 2012, 10:26 AM
Thread: Whipper Snipper Fuel/Oil mix
by parkinson- Replies
- 9
- Views
- 26,684
Personaly I would mix it 25:1 as.per manual if...
Personaly I would mix it 25:1 as.per manual if it's running rich it will only burn more oil causing it to blow abit more blue smoke, better to go thro abit more oil then risk running it to dry...
-
14th February 2012, 08:37 PM
Thread: Wiring a push buton switch
by parkinson- Replies
- 8
- Views
- 2,014
Pm sent. I think if worked anyway let us know...
Pm sent.
I think if worked anyway let us know if u recive it
Scott -
13th February 2012, 07:15 PM
Thread: Wiring a push buton switch
by parkinson- Replies
- 8
- Views
- 2,014
Take a picture of the back (Terminals) and front...
Take a picture of the back (Terminals) and front of the switch, so we know what your talking about.
scott -
13th February 2012, 05:42 PM
Thread: best welder for Gal?
by parkinson- Replies
- 10
- Views
- 3,459
Inreality it's better to just grind the gal off...
Inreality it's better to just grind the gal off before u weld. In my experience I believe that the mig is alot easier to weld with. Depending on how much and what u weld in regards to weather your...
-
13th February 2012, 10:12 AM
Thread: Parkanson power hacksaw
by parkinson- Replies
- 60
- Views
- 7,481
Hey Dave did u end up.getting it all working. Did...
Hey Dave did u end up.getting it all working. Did u sort out the hydraulics? I have 2 one is the same as yours (6"-6") and maybe a few years later and the other is older but is huge (12"-12"). When I...
-
NEW NEW NEW NEW NEW NEW NEW G'day no it...
NEW NEW NEW NEW NEW NEW NEW
G'day no it doesnt seem to be stuck on it will move from side to side but not up. Any way i took the ram plunger out that lifts the boom and discoverd that the o-ring... -
NEW NEW NEW NEW NEW NEW NEW G'day no it...
NEW NEW NEW NEW NEW NEW NEW
G'day no it doesnt seem to be stuck on it will move from side to side but not up. Any way i took the ram plunger out that lifts the boom and discoverd that the... -
I removed the main lift arm (hydrolic rams...
I removed the main lift arm (hydrolic rams plunger) and discoverd that the o-ring on the end was bugged so i will get a new one tommorow.I think that would have been a big contribution to my problem...
-
power hacksaw
Its not near as well used as the pic show it doesnt leak oil any except where the cams are from oil running a little fast throught them, and it is also two speed (two diffrent sets pullys to change...
-
162726 162727
162726
162727 -
Here's some pics of it i suspect that it may have...
Here's some pics of it i suspect that it may have been repainted because i am yet to see one the same colour. also do u know some where that i can get 22" (550mm) blades at a good price.Thanks
... -
26th February 2011, 09:33 PM
Thread: Help with electric motor
by parkinson- Replies
- 28
- Views
- 3,070
electric motor
Anyway how did you get on with motor. If your really stuck and can wait i am a 3rd year apprentice and have trade school in 4weeks and 2 out of the three of my teachers are old time rewinders. thanks
-
parkanson
g'day everyone I have just brought a parkanson power hacksaw (12"x12") and have noticed that a few things need adjusting like the feed control if it is set on the feed control it will go down and hit...