Search:

Type: Posts; User: DaleBlack

Search: Search took 0.07 seconds.

  1. Replies
    14
    Views
    10,907

    i thought the screw head sits deep down beneath...

    i thought the screw head sits deep down beneath the brown plastic rig not just the softer oring in the lighter colour?
  2. Replies
    14
    Views
    10,907

    I have solid oak chairs where the front legs are...

    I have solid oak chairs where the front legs are straight but rear legs on a angle.

    I have polished solid wood floors.

    Slipstick Sliders CB210 and CB215 | Slipstick Foot

    455296

    The above...
  3. Hi Fuzzie I think you are right I used my...

    Hi Fuzzie

    I think you are right

    I used my vernier gauge and the Top of the metal head (ie w the wedge) oval shaped is smaller . Its 31mm wide by 41mm long.

    The bottom of the metal head is...
  4. Hi Fuzzie "Did you note a flare in the hole...

    Hi Fuzzie

    "Did you note a flare in the hole through the head when you started? "

    one can never take enough photos! i should have taken some of the head. I did ensure that the end of the head...
  5. I just sent the images from my initial post to...

    I just sent the images from my initial post to Cyclone.com.au support and they said it was on the right end and its meant to be belted down until the head comes up firm against the wider part of the...
  6. Cheers for the responses guys, so would i be...

    Cheers for the responses guys,

    so would i be overconfident thinking i had the luck that the handle happened to fit perfectly and is well expanded against the sides of the metal head w requiring...
  7. Sledgehammer Handle Replacement - Do you need wood and metal wedges?

    Hi

    I had a spare sledgehammer head after the old handle broke. I think it was a cheap Triton sledgehammer from Bunnings, last about 5 years.

    I went and purchased this cyclone spotted gum...
  8. Topcoating a existing painted surface - outdoor garden bench seat

    Hi

    I recently posted a thread about repainting white a varnished wooden daybed.

    Garden Bench Seat
    <!--[if gte mso 9]><xml> <w:WordDocument> <w:View>Normal</w:View> <w:Zoom>0</w:Zoom> ...
  9. I will use oil based for the primer, but due to...

    I will use oil based for the primer, but due to yellowing i was going to use water based dulux aquaenamel for the 2 x topcoats. Are you saying this is okay or that I should be oil based for the...
  10. What liquid (solvent) to moisten a wrag with to clean dust from scuffed varnish coat

    Hi guys, thanks for the replies.

    I have almost scuffed (no dremel :>) the entire piece with 120 grit.

    I will vacuum the dust off with a bristle tipped std vacuum. I dont have a compressor at...
  11. Hi Arron I have seen that product and was...

    Hi Arron I have seen that product and was skeptical. If i combine it with the type of scuff up you can already see, I should put myself in a good position for Zinsser over the top?
  12. Hi all thanks for the responses. That Lee...

    Hi all

    thanks for the responses. That Lee Valley has some quality stuff

    also saw these

    3M™ Ultra-Flexible Sanding Sheets
    3M™ Ultra-Flexible Sanding Sheets - Lee Valley Tools
  13. Dremel or similar tool to sand small intricate carved parts on wood

    I have posted this in part (along with paint questions in the general section) - I see this is for Dremels so also posted here

    See these intricate parts on the daybed

    412574412575412576


    I...
  14. Also meant to add, can you link the oil based but...

    Also meant to add, can you link the oil based but non yellowing Aquaenamel Dulux product?

    They have a oil based range as below

    https://www.dulux.com.au/products/378

    I just check with them...
  15. Hi thanks for the quick response Tonzeyd ...

    Hi thanks for the quick response Tonzeyd




    Can I ask specifically with the Dremel, will it make the laborious hand sanding faster on the intricate parts? or do you see those attachments i...
  16. Sanding and Priming a Varnished Daybed to paint white

    Hi I have a wooden daybed as below. I think its from Indonesia so not sure the wood type. I believe its varnished as where I have sanded there is a white powdery substance.

    I have been using 120...
  17. I had one response from the Cabots Contact Us line

    I had one response from the Cabots Contact Us line
  18. Good Sealers for Hardwood Table tops like Marri to preserve natural look

    359631359632The one on the left, Acrylic preserves the natural look of the timber whilst the marri on the right has been yellowed. I prefer the natural look personally.

    Apparently they achieve...
  19. Hi all I was pondering the idea of the...

    Hi all

    I was pondering the idea of the 'stretcher' myself though didnt realise the word is stretcher for it. I was ready to set off to bunnings tonight to buy some pine and then I realised that...
  20. Converting troublesome Wooden drawer runners to Metal runners

    Hi

    I have some wooden drawer runners on a cot, not only are they stiff and are not smooth in operation but it falls out quite easily. It falls out well before full extension, partly because the...
  21. Capping to go along a brick wall - knee height

    In my patio area I have a L shaped zone separated by one pillar. So 2 rectangles of
    235mm (two std bricks width) by 1290mm long and the other by 1640mm long.

    What types of relatively simple...
Results 1 to 21 of 21