Search:

Sold!!

Pm sent
Thanks Greg

Thanks Chi4S

None in stock, will have to buy from the states.

Cheers Michael

Hi guys

Quick question on where to buy pokeys55/56 from australia, Have bought one before but lost memory were I got it from. :?
Any help would be appreciated.

Cheers Michael

Hi Russell

Some of this might help.

Diy steel router build - Page 3 - CNCzone.com-The Largest Machinist Community on the net!

Thanks guys
Sounds like a challenge :2tsup:

Michael

Hi Bob

Will be following this thread closely as i need to do the same thing with my vfd.
Just one thing i noticed (could be wrong) your spindle relay is set to output #1 and your output signal...

Hi
cable is --Siemens Australia 5EMC4105 4x1.5 sq.mm (0,6/1 kv)
I use this on 72vdc 1070 ozin motors.:o
Also will change the router 240v lead to a 3 core shielded cable as this causes the most...

yes $3.50 mtr, its very flexible which mine was running at 100mm radius on my cnc router.
To give you some idea, its a extension lead with braided wire and a clear sleeve.
here is some pictures of...

Hi

I know where to buy shielded cable in perth by the meter, but high or low frequency I dont know, all I can say on that one is any shielded cable is better then none.
The larger cables seem to...

Last update before xmas, next is to buy the 12mm ali plate for the table top and I will also put a plate on the front of the table as this will come in handy for facing edges .

Cheers Michael ...

Time for some updates, Z axis nearly completed.

Cheers Michael

Here's a second hand one, Dont know if its any good to you.

Used Machinery - Welcome to Bill's Machinery - Used Machinery Dealers

Cheers Michael

Put in a few hours after work,

Cheers Michael

Up all night cutting 16mm plate aluminium for the y axis, need to get some more cap screws to fix it together, should have this on during the week, Think sunday is rest day for me :sleep5:
...

Hi Ch4iS

The 6mm steel plate is 200mm wide with 40mm tube down the side, which i stich welded and i ended up with a .5mm bow so i tried to staighten it by driving my 4wd over it :oo: it...

Thanks Rod

And yes those motors are 1076 ozin, I have a box full so I put 3 on ebay just to see what they go for.
Next will be the water or air cooled spindle from china, not shore which is the...

Hi guys
I mainly hang around the cnc zone but always hinding here in the shadows.
Yes the side gantry is 6mm plate steel with 40mm tube down the sides very strong.
My cnc is very heavy with feet...

Hi Rod

Spoke to a different guy at capral and was given the wrong price on 16mm plate.
About $80 so i will go 16mm plate on the (Y) axis.

Thanks for pointing me in the right direction,...

Thanks Rod. Will go for 12mm. Now I better get back to work. Cheers Michael

Have priced up 16mm ali at capral in malaga, about $250 Thanks Michael

Thanks for that Rod. I think I have these going the other way around, thats why I'm confused.every thing I cut comes out ok but untill now !! I better check all my settings. cheers Michael

Sorry my mistake , I meant the z axis, every thing stays as you see in picture. cheers Michael

Hi guys

What would be a good thickness aluminium plate for my x axis, it will be 150mm width

any advise !!

cheers Michael

Any perth guys looking for sheilded cables can buy from ElectCables in Kewdale, they sell it by the mtr,i purchased some 4x1.5mm2 shielded for $3.50 mtr and last time i went to get some 3x1.5mm2...

I know they meet at mcdonalds in Vicpark one sunday a month
Never seem to get there.:doh:
michael

Found this on the cnczone some where, unzip and paste it into your mach3 file, then open mach3, go to veiw and click on load screens and click on the file and presto !!
it puts a auto tool zero...

Good to see you have sorted out your problems with your faulty drive Geoff,
I see you live about 10 minutes from me, maybe we can exchange ideas as there is so much to learn.

Michael.