Search:
Type: Posts; User: dimma20
Search: Search took 0.00 seconds.
-
5th July 2015, 12:13 PM
Thread: Refitting Poly V-Belt on JET JWSS-10LFR
by dimma20- Replies
- 2
- Views
- 970
Thanks Ross - I have re-attached and made sure it...
Thanks Ross - I have re-attached and made sure it was aligned properly - runs smoothly when turned on and off. I'll see how it goes under load when cutting. Appreciate your feedback. Cheers, John:U
-
2nd July 2015, 09:28 PM
Thread: Refitting Poly V-Belt on JET JWSS-10LFR
by dimma20- Replies
- 2
- Views
- 970
Refitting Poly V-Belt on JET JWSS-10LFR
Hi,
The poly v-belt on my Jet JWSS-10LFR slipped off while running (the drive belt from the motor) not the height adjustment one. I turned the machine off immediately and found it easy to re-fit... -
14th September 2010, 08:11 PM
Thread: Bandsaw Fence
by dimma20- Replies
- 4
- Views
- 1,222
Bandsaw Fence
Thanks all for the info - including the link to Luna. The Kregg fence looks promising - I'll try and check one out at Carbatec. Thanks again, John.
-
14th September 2010, 02:11 PM
Thread: Bandsaw Fence
by dimma20- Replies
- 4
- Views
- 1,222
Bandsaw Fence
Hi,
I was wondering whether anyone had thoughts on where to source a rip fence that is able to be retro fitted a second hand bandsaw. The bandsaw is Luna (Swedish) 21inch - 3 phase and when I... -
7th October 2008, 08:31 PM
Thread: Anyone know what this is?
by dimma20- Replies
- 64
- Views
- 8,181
Teardrops mmmmmmm perhaps - I can think of an...
Teardrops mmmmmmm perhaps - I can think of an application 'a la Guantanemo; which might bring tears to one's eyes - well at least half the population's eyes!
-
27th May 2008, 10:08 PM
- Replies
- 10
- Views
- 2,889
Exactly the same thing happened to mine - albeit...
Exactly the same thing happened to mine - albeit after a few years good service. The bearing housing also started to grumble shortly before it pooped itself completely - solution a new Bosch Orbnital...
-
23rd May 2008, 09:01 PM
Thread: employee rights
by dimma20- Replies
- 25
- Views
- 3,482
Hi, I have worked in HR/IR for 30 years and...
Hi,
I have worked in HR/IR for 30 years and the above posts cover most scenarios pretty accuaretly. If you don't give the required period of notice specified in the relevant employment instrument... -
6th May 2008, 10:27 PM
Thread: Timber Challenge II Congrats Comments
by dimma20- Replies
- 110
- Views
- 11,215
Great work all round! Some really exquisite...
Great work all round! Some really exquisite pieces.
John:2tsup: -
6th May 2008, 08:44 PM
- Replies
- 8
- Views
- 2,120
A good laugh! John:U
A good laugh!
John:U -
6th May 2008, 04:53 PM
Thread: Makita Drop Saw
by dimma20- Replies
- 1
- Views
- 3,005
Makita Drop Saw
Hi,
Does anyone have a manual for a Makita 2400B drop saw and wouldn't mind sharing a copy. Am looking at buying one - these were a great model and extremely durable. Thanks and much appreciated... -
28th April 2008, 11:00 PM
Thread: Super cheap TRITON Router Bits
by dimma20- Replies
- 48
- Views
- 7,413
Thanks also for the tip Stu, Got a few last week....
Thanks also for the tip Stu, Got a few last week. Cheers, John. :roll:
-
21st February 2008, 08:10 PM
Thread: Manual for Jet SuperSaw JWSS-10FLR
by dimma20- Replies
- 2
- Views
- 2,884
Thanks David - Much appreciated. John:2tsup:
Thanks David - Much appreciated. John:2tsup:
-
21st February 2008, 07:58 PM
Thread: Manual for Jet SuperSaw JWSS-10FLR
by dimma20- Replies
- 2
- Views
- 2,884
Manual for Jet SuperSaw JWSS-10FLR
Hi,
I was wondering if anyone has a copy (or could pdf a copy) of a manual for a Jet SuperSaw JWSS-10FLR. I have purchased one second hand but the previous owner could not find the manual. It's... -
29th January 2008, 09:20 PM
- Replies
- 10
- Views
- 1,913
Thanks everyone for great advice -really...
Thanks everyone for great advice -really appreciated. I was a bit hesitant about the dead center but now will proceed with renewed confidence...and a little lubricant of course!
Thanks again -... -
29th January 2008, 07:57 AM
- Replies
- 10
- Views
- 1,913
Thank you Joe - good advice. You are spot on...
Thank you Joe - good advice. You are spot on with your description and given I paid only 50 bucks and got at least half a dozen good chicels with it I agree it is better to persevere for now. Also...
-
28th January 2008, 10:09 PM
- Replies
- 10
- Views
- 1,913
Thanks Bob - a photo would be helpful. Regards,...
Thanks Bob - a photo would be helpful. Regards, John.
-
28th January 2008, 09:49 PM
- Replies
- 10
- Views
- 1,913
live center with 1/2 inch thread rather than MT
Hi,
I have recently purchased a small lathe from an old clock maker/repairer. It is fairly basic (indeed primative is probably a more apt description). Anyway my problem is the tailstock has a...